McCulloch Chain Saws

[buzz sawyer]

Is anyone familiar with replacing the primer cup on the old super 33?

 

[heimannm]

buzz - I know I've done it but I don't remember any details other that the plug/screw comes out of the bottom and the whole assembly comes out that way.

If you don't have an IPL let me know and I can try to send one, they are pretty big files.



Mark

 

[Rallyeguy]

Hi Gang,
I just added a quick link to my current McCulloch IPL and Service Manual Library at my Old Saw Shop Store. I intend to add files as I gather them...Free for anyone that needs them. https://www.oldsawshop.com/McCulloch-IPL-Library-c148775760

 

[david newbie]

Just picked up a mcculloch 300. Turns over but in need of TLC. Should I post it or give it a scrap metal guy?

 

[buzz sawyer]

buzz - I know I've done it but I don't remember any details other that the plug/screw comes out of the bottom and the whole assembly comes out that way.

If you don't have an IPL let me know and I can try to send one, they are pretty big files.

View attachment 1166515

Mark

Thanks Mark, I'll see if I have an ipl. What you sent may be enough. The saw runs great, just needs a prime to start. Found the cup on ebay last month.

 

[cbfarmall]

Checking around, but I am hoping to find some standard bore thin rings, part # 58353, for my 895. You could drive a truck through this gap. Manual says it's supposed to be .004 to .012. If I strike out with OEM, I'm thinking about trying some Pioneer thin rings.

 

[heimannm]

Inventory says I have them Chris, $24.95 + shipping.

Come up with some other stuff to help spread out the shipping cost.

Mark

 

[cbfarmall]

Inventory says I have them Chris, $24.95 + shipping.

Come up with some other stuff to help spread out the shipping cost.

Mark

Nice. How about the piston pin bearings? 62867 and 62868. The ones I used came out of another NOS piston and I'd like to replace them.

 

[heimannm]

Chris - I sent a PM. Looks like I have all the parts, but the bearings are different numbers. I'd like you to confirm the dimensions are .5x.6875x.5, one open end one closed end.

I have the pawl springs as well.

Mark

 

[buzz sawyer]

Is anyone familiar with replacing the primer cup on the old super 33?

Just finished replacing the cup. It was a little tight going over the bottom of the plunger but it works fine now. I know because first thing I did was flood it. Need to adjust the idle speed, will post a video.

 

[Rallyeguy]

Good morning all,

I added two gear drive gaskets to my store this week. Figured some of you might have a need.

Part # 51609A https://www.oldsawshop.com/Large-Frame-Gear-Drive-Cover-Gasket-p644583009
Part #68639 https://www.oldsawshop.com/Large-Frame-Gear-Drive-Cover-Gasket-p560045769

Planning on adding more gear drive gasket stuff as I can...

Thanks,

Brian Genrich

 

[buzz sawyer]

Just finished replacing the cup. It was a little tight going over the bottom of the plunger but it works fine now. I know because first thing I did was flood it. Need to adjust the idle speed, will post a video.

In case anyone is looking for this primer cup - https://www.ebay.com/itm/176226312176
It's a little longer than the original but fits and works well.

 

[bob kern]

Friends at work got me a shirt for a retirement gift!

 

[Jeffrey F.]

In case anyone is looking for this primer cup - https://www.ebay.com/itm/176226312176
It's a little longer than the original but fits and works well.

I had some on eBay and only sold 1 in a year so I took them down ??

 

[buzz sawyer]

I had some on eBay and only sold 1 in a year so I took them down ??

Try listing again. I hated to pay that much but figured I'd never find another one and the saw was free. The 33 is a pain to start cold without a prime since it has no choke.

 

[Brufab]

Does anyone know anyone who would re ring a thin ring Mac 1-72? I have 90# compression, p&c look pristine and saw is really clean. Rings do move so there not stuck or frozen.

 

[InvictusRisen]

Does anyone have a lead on p&c for a pm700? Or is Lil Red Barn the only place that makes pistons?

 

[Squareground3691]

New Hoodie Day ,

 

[knightmax]

Does anyone have a lead on p&c for a pm700? Or is Lil Red Barn the only place that makes pistons?

I sold my last PM700 NOS cylinder two weeks ago. I have NOS 7-10 cylinders. Same cylinder just pre electronic ignition. PM me if you want more information.

 

[Brufab]

Just picked up a mcculloch 300. Turns over but in need of TLC. Should I post it or give it a scrap metal guy?

Probably post it, might be what a guy needs to get another saw running???