ArboristSite.com Sponsors
 
 



 
 


Results 1 to 9 of 9

Thread: 032 ignition help???

  1. 05-04-2008, 03:04 PM #1
    Trever
    Trever is offline
    Senior Member
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Trever's Avatar
    Join Date
    Mar 2006
    Location
    East TN
    Posts
    380
    Credits
    67

    032 ignition help???

    Does the 032 and 031 share the same points, condensor, and coil? My 032 needs new points and I am not sure about the condensor. Is there anyway to test a condensor; ohm meter? Thank you.
    Trever

    Stihl 075 AVE(TS760 filter), 034AVEQ(heated handles), MS 260 Pro, MS 192T, TS760 to 076 Super
    Dolmar 116si
    Strunk Big Machete project (105cc West Bend)
    '93 KTM 125cc in the making... ONE OF THESE DAYS
    GB 44" Double ender CSM
    Mini Mill, Beam Machine
    Belsaw M14 with Detroit 4-53 non turbo
    MAXX grinder
    I NEED A MILL AND A LATHE!!
    CAD......YEP!!!
    Reply With Quote Reply With Quote
  2. 05-04-2008, 03:38 PM #2
    tomdcoker
    tomdcoker is offline
    Arboristsite MVP
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Join Date
    Sep 2005
    Location
    North Miss.
    Posts
    1,192
    Credits
    461
    To test the condenser, use your ohm meter set on resisatance and you should see a small rise of the needle and then it will fall back to zero. Tom
    TOMTINKER
    Reply With Quote Reply With Quote
  3. 05-04-2008, 04:20 PM #3
    Trever
    Trever is offline
    Senior Member
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Trever's Avatar
    Join Date
    Mar 2006
    Location
    East TN
    Posts
    380
    Credits
    67

    Thanks

    Thanks Tom. I will try it.
    Trever

    Stihl 075 AVE(TS760 filter), 034AVEQ(heated handles), MS 260 Pro, MS 192T, TS760 to 076 Super
    Dolmar 116si
    Strunk Big Machete project (105cc West Bend)
    '93 KTM 125cc in the making... ONE OF THESE DAYS
    GB 44" Double ender CSM
    Mini Mill, Beam Machine
    Belsaw M14 with Detroit 4-53 non turbo
    MAXX grinder
    I NEED A MILL AND A LATHE!!
    CAD......YEP!!!
    Reply With Quote Reply With Quote
  4. 05-04-2008, 05:11 PM #4
    Lakeside53
    Lakeside53 is offline
    Stihl Wrenching
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Lakeside53's Avatar
    Join Date
    Dec 2004
    Location
    Woodinville, WA
    Posts
    24,831
    Credits
    103
    If you need new points, it's often because the condersor has failed.
    Any sufficiently advanced technology is indistinguishable from magic."
    --Arthur C. Clarke,
    Reply With Quote Reply With Quote
  5. 05-04-2008, 06:52 PM #5
    Trever
    Trever is offline
    Senior Member
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Trever's Avatar
    Join Date
    Mar 2006
    Location
    East TN
    Posts
    380
    Credits
    67

    Thanks again

    Tom and Andy,

    Thanks for your help. you just reminded me to load up me 032 tonight and take it to work with me tomorrow. I will try the ohmeter test on the condenser.
    The points look really black on the contacts. I will try to clean it up some with some emory cloth. Anything else I can try? Thanks.
    Trever

    Stihl 075 AVE(TS760 filter), 034AVEQ(heated handles), MS 260 Pro, MS 192T, TS760 to 076 Super
    Dolmar 116si
    Strunk Big Machete project (105cc West Bend)
    '93 KTM 125cc in the making... ONE OF THESE DAYS
    GB 44" Double ender CSM
    Mini Mill, Beam Machine
    Belsaw M14 with Detroit 4-53 non turbo
    MAXX grinder
    I NEED A MILL AND A LATHE!!
    CAD......YEP!!!
    Reply With Quote Reply With Quote
  6. 05-04-2008, 06:59 PM #6
    Lakeside53
    Lakeside53 is offline
    Stihl Wrenching
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Lakeside53's Avatar
    Join Date
    Dec 2004
    Location
    Woodinville, WA
    Posts
    24,831
    Credits
    103
    btw.. the ohmeter check is only a rough guide.. a real point condensor tester tests it under 250 volts or so... it's not uncommon to see "capacitance" with an ohm meter, but the failure under real world conditions.
    Any sufficiently advanced technology is indistinguishable from magic."
    --Arthur C. Clarke,
    Reply With Quote Reply With Quote
  7. 05-04-2008, 07:13 PM #7
    Trever
    Trever is offline
    Senior Member
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Trever's Avatar
    Join Date
    Mar 2006
    Location
    East TN
    Posts
    380
    Credits
    67

    031 032 parts

    Andy,

    Does the 031 and 032 share the same points and condenser?
    Trever

    Stihl 075 AVE(TS760 filter), 034AVEQ(heated handles), MS 260 Pro, MS 192T, TS760 to 076 Super
    Dolmar 116si
    Strunk Big Machete project (105cc West Bend)
    '93 KTM 125cc in the making... ONE OF THESE DAYS
    GB 44" Double ender CSM
    Mini Mill, Beam Machine
    Belsaw M14 with Detroit 4-53 non turbo
    MAXX grinder
    I NEED A MILL AND A LATHE!!
    CAD......YEP!!!
    Reply With Quote Reply With Quote
  8. 05-04-2008, 07:25 PM #8
    Lakeside53
    Lakeside53 is offline
    Stihl Wrenching
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Lakeside53's Avatar
    Join Date
    Dec 2004
    Location
    Woodinville, WA
    Posts
    24,831
    Credits
    103
    same condenser; different points.
    Any sufficiently advanced technology is indistinguishable from magic."
    --Arthur C. Clarke,
    Reply With Quote Reply With Quote
  9. 05-04-2008, 07:43 PM #9
    Trever
    Trever is offline
    Senior Member
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation
    Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation Reputation     Trever's Avatar
    Join Date
    Mar 2006
    Location
    East TN
    Posts
    380
    Credits
    67

    031 032 parts

    I know where 2-3 junked 031s are. I will grab a condensor off of one and give it a try. Thanks again.
    Trever

    Stihl 075 AVE(TS760 filter), 034AVEQ(heated handles), MS 260 Pro, MS 192T, TS760 to 076 Super
    Dolmar 116si
    Strunk Big Machete project (105cc West Bend)
    '93 KTM 125cc in the making... ONE OF THESE DAYS
    GB 44" Double ender CSM
    Mini Mill, Beam Machine
    Belsaw M14 with Detroit 4-53 non turbo
    MAXX grinder
    I NEED A MILL AND A LATHE!!
    CAD......YEP!!!
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Page generated in 0.16527 seconds with 43 queries [Server Loads: 6.97 7.46 : 5.40]