redunshee
Addicted to ArboristSite
Never tried.
Nik's Poulan Thread
- Thread starter FATGUY
- Start date
Help Support Arborist Forum:
Bob, you just need to know who to ask? how does that Mastermind 4000 run?
Because they are NLA and have been for quite some time. Besides the seals like the SKF are much cheaper than a OEM would have been, and they work just as good.
The seals are sitting in many old saw shops just wanting to be installed in our saws. just need to ask for them in most cases.
ANewSawyer
Addicted to ArboristSite
. I am guessing that this is the SKF seal alluded too because the 253747 is what I have been having such a hard time with. Note: fossil says the 253747 is a double lip but mine have all been single. Factory was a double lip though.
I posted earlier...you want these. They are fresh and common to some other saws. I keep them on hand.
ANewSawyer
Addicted to ArboristSite
I missed that, thank you, thank you, Thank you!
Where do you get them from? All I have around here is auto part stores and tractor supply.
Where do you get them from? All I have around here is auto part stores and tractor supply.
redunshee
Addicted to ArboristSite
Believe it or not I have yet to cut with it. Just start it up every so often. Just like all my saws here in Texas.
blk05crew
I like 'em green
Spent about 3 hours last night finishing up the Craftsman 4.2. Got the new piston and rings installed, made a new base gasket, put in new crank seals, new fuel line, cleaned the carb, cleaned the inside of the muffler out and painted the outside because I'm a dork like that. Set the carb to 1 turn on H and just over 1 turn on L. Fired right up after about 4 pulls and adjusted the idle just a bit. Runs fantastic and couldn't be happier with it!
Sty57
Tree Freak
Looks good Nate. What Echo bars are you running that fits them? I need a new one for my 5200.
Another 3500 yesterday on bench 1, as on right now on hold. Also on bench 2 3.3 365 3500 3450, 35 34 both on hold too, bench 3 260 and all the th's I need to finish putting back together. All 3 run now. All can be sold or traded if interested. Not married to any chainsaw 
blk05crew
I like 'em green
Thanks! Honestly, I'm not sure what mount it is. I got it a while back and it's the same bar that was on the 5200, I don't have multiple. I need to get another 24"-28" bar and chain for my 5200 as well.
blk05crew
I like 'em green
Another 3500 yesterday on bench 1, as on right now on hold. Also on bench 2 3.3 365 3500 3450, 35 34 both on hold too, bench 3 260 and all the th's I need to finish putting back together. All 3 run now. All can be sold or traded if interested. Not married to any chainsaw
View attachment 533330 View attachment 533331 View attachment 533332 View attachment 533333
I think Brian, (Sty57) was actually looking for a 3450 if I remember right.
This one pulled 180psi stock, about as new as you can get without getting nos. Right now on hold pending $$$.
IMO no dont do it. Will it do it yes but will be hard on it IMO.
475 pulls 37" full comp fine and full skip too. But I use 7. Sold as 36" bar but is 119dl and 1 inch longer then my other 36" I had so I call it 37"
Was testing with bar above to see if the homemade metal clutch cover from 268-272 would clear noodles better then the stock ones.
Failed
Failed
Yep 8 for speed cuts on small wood.
Heck I put a 8 on the 65cc 415 to see if it could pull the chain I made for a 3120.
Similar threads
