Search results

Hi, I have a fairly large tree next to my house that I've noticed some rot in. Is this definitely beyond repair and ready to be cut down? Or should I have an arborist look at it? You can see my 3.5in knife sunk into one spot. Sent from my SM-G960U using Tapatalk

Husqvarna 576xp. I bought it with a scored piston and some mild transfer in the cylinder. I cleaned up the cylinder and put a new Golf piston and Caber rings in it. I'm putting it back together now. Will be ready to ship out in a couple days. $425 pho shipped east of the Mississippi. Add $10...

This may be an unlikely trade, but I figure I'll give it a shot. I got the 36" bar in a trade and thought I'd keep it for my 460 in case I needed that much bar in a pinch. Well, I needed it in a pinch, but the 460 won't oil it, so I'd like to trade it for a light 28 or 32 bar. Looking to...

Looking to sell a Husqvarna 550xp. It starts right up and runs good. Piston looks good, no scoring, some oil staining. Small broken piece next to kill switch, see pictures. Saw is a little dirty, could use a good cleaning. I did give it a quick wipe down for the pics. Note that the pics make...

This is an ugly 394xp that runs. I got it from a guy that said it didn't have spark. I took the starter cover off, checked out the kill switch wire and spark plug wire. Turned it over with a drill and there was spark. Put it back together, put some mix in the carb, and it started up...not sure...

Looking for muffler and rear filter cover for MS441.

SOLD SOLD SOLD SOLD SOLD Selling Stihl MS362. It starts up and runs. It's fully functional, but it was in a fire and has some smoke staining and heat damage. The top cover and top handle were replaced by the previous owner. I was going to replace the ugly parts, but I'm just going to pass it...

Looking to sell Stihl 261C-M. Starts right up and runs and cuts good. I put a new OEM piston in it because it had some varnish buildup on the piston. There is a small scratch below the exhaust port, but it won't affect anything because it's not above the port. I can get any additional detailed...

I bought an MS 261 CM not too long ago. It starts up, runs good. It has 160 psi compression. I started the process of selling it because I need the money. I pulled the muffler off to take some pics of the piston and was surprised to see that most of the piston is a dark color, as if it is...

Looking to sell Stihl 261C. Starts right up and seems to run good. Could stand to be cleaned up a bit. I can get any additional detailed pics anybody wants. Looking to get $450 plus shipping PHO. Could work out a deal for a 18" bar and chain if interested.

Selling Husqvarna 55 Chainsaw. I bought it as a project and don't have the time to finish it. It has a scored piston, that's as far as I got with it. I bought an aftermarket cylinder/piston kit (from HL Supply). It's a pretty nice looking saw. Plastics are nice and have nice color, just a few...

Looking to sell used OEM Stihl 034 Cylinder. It had some aluminum transfer so I cleaned it up with 180 and 320 grit on a Foredom, then red scotchbrite. Will need rinsed out and off. Looking to get $50 shipped.

Looking for good used MS290 cylinder. 46mm. Let me know if you have one for sale and what you're looking to get for it?

Selling a Husqvarna 372xp. It starts, but dies right away, assume it needs carb kit, fuel line, etc. I was going to go through it and get it up and running, but I'm looking to buy a Kombi system next week and need the money for it. I can take more pics, these are just what I have on my phone...

Stihl 046 for sale. Bad: Rough looking. Needs fuel system overhaul. Rear handle is broken, but previous owner repaired it with aluminum plate and has lasted for 10 years so far he said. Had a small chip in front of case that weeped oil, previous owner JB Welded. Crack in muffler cover. Leaks...

I'm cleaning up a cylinder on an MS 290. Once all the aluminum was cleaned off, I can see that there are some scratches in the plating, and I wore though the plating in one small spot under the exhaust port. If it was just one scratch, I wouldn't even ask, but there are several, plus where I...

Husqvarna 550xp. Runs and cuts as it should. Good condition. I was going to keep to compare to my 026, but I haven't had a chance to use it yet, and I'm trying to buy a loader for my garden tractor. $400 plus shipping. Will trade toward a John Deere 40 Loader within 3 hours of central PA.

Looking to buy a very clean 026 for my buddy. I have one and he wants one like it. Let me know what you have and send me some pics and a price. Thanks.

Selling a Stihl 036. Starts easy and runs and idles well. Holds idle when turned on all sides. Not the prettiest machine. I gave it a quick wipe down, but could use a thorough cleaning. Seems top have some sap on the front and top cover. 145psi compression. Looking to get $275 PHO plus shipping.

Looking for the following parts: Top handle Top AV mount Early 024 air filter Ring that goes inside the intake neck Ring that goes outside the intake neck on the carb studs 4 starter screws including the one that holds the chain brake handle. I'd love if someone has all of the parts. I won't...