Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. MustangMike

    Removing stuck MS460 clutch drum

    I recently got my first "project saw", an MS 460. It is dirty, the cylinder is off and the engine seemed to be locked (presumed bearing failure). To my surprise, the P&C look good. However, as I was taking it further apart, I believe the problem may be just the clutch bearings, as the clutch...
  2. MustangMike

    Stihl 044 gas caps

    My 044 #2 (orig tank) has been leaking gas lately. I had previously repaired the vent, but this time it seems to be coming from the cap. I exchanged the cap with the one that was on the old 044 #1 tank holder, the rubber gasket on that one looked real good, but it is still leaking, and it...
  3. MustangMike

    Stihl 28" B&C question

    When I install a 28" B&C (91 link) on my 044 the actual cutting length is 27" (not 28"). Has anyone tried to install the 93 drive link chains, or will this create problems?
  4. MustangMike

    Stihl KM130R Problem

    OK, not a chainsaw, but close! It runs fine, but it stopped powering the attachments today, and the attachment I pulled out seemed to be oil dry instead of wet like they usually are. I mostly use the cycle bar with it. Anyone familiar with what usually goes wrong with these things? I'm...
  5. MustangMike

    Rough Night, Prayers will not hurt

    Got a call from my daughter about 9:30 last night. Seems that both her 6 yr old son and Husband were in the Hospital. The six year old was going up the stairs to go to bed when he tripped and split his lip badly. There was a lot of blood, so it looked worse than it was, so his 41 year old...
  6. MustangMike

    Just Some Saw Wts

    Just thought I would post some of my saw wts. Nothing scientific or anything. All saws are fueled, and I just used a bathroom scale, so I do not say it is 100% accurate, but the the comparative wts (1 saw to the next) are what counts. 362 C w/20" b&c 17.4 lbs 044 w/20" b&c...
  7. MustangMike

    A Felling Question

    I know there are a lot of people on this site with a lot more experience/knowledge than me, so I'd like some feedback from you on a felling question. There is a tree with a slight lean to it. I want to drop the tree at about 45 degrees from the lean. I'm thinking to make the notch in the...
  8. MustangMike

    Stihl Square File Loops

    Hey, I just discovered that one of our sponsors, Baileys Chainsaw, now sells Stihl Square File Chain in loops, and their prices are not bad! Last year when I started using square, I had to buy rolls and have the chain made. This should make it a lot easier for anyone who wants to try the Stihl...
  9. MustangMike

    Playin with 044 #2

    Most everyone on this site knows how much I like the 10mm 044s, and how nicely they responded to air filter and exhaust mods. So I decided to play with 044 #2 to see if I could get even more out of it on my own. I considered deleting the base gasket, but when I measured the squish, it was...
  10. MustangMike

    Looking For MS440 or 12 mm 044 Parts Saw

    I posted this in the Trading Post section, but not much response. I want to build a 440/460 hybrid, so I'm basically looking for a complete saw in good condition that has a fried P&C. If anyone has something, I'd appreciate a PM. Thanks
  11. MustangMike

    362 C-M Cold Weather Starting

    I've noticed that my 362 C-M (ported) seems to start easier in the cold weather if I do not use the Compression Relief. Anyone else notice this with a C-M saw? Does the impulse line function better when U don't use CR? After it is warm, even if I have not run it for 5 min or so, it starts...
  12. MustangMike

    Want to Buy Stihl 12 mm 044 or MS440 Parts Saw

    I'm looking for a 12 mm 044 or MS 440 (with a fried cylinder) to use as a parts saw for a Hybrid 440/460. If U have what I'm looking for, please let me know. Thanks, MustangMike
  13. MustangMike

    HELP - Trouble with 044 #2

    I've been having trouble with 044 #2. It started a few weeks ago out of nowhere (it ran great the previous outing). When cold, the saw will run for 20 or 30 seconds, then die. After that, you can get it to start but as soon as it reaches full RPM it dies. I replaced the spark plug & fuel...
  14. MustangMike

    ID This Old Truck

    I posted these pics in "Scrounger" thread w/o much response, but I figure there must be some motorheads on here that can provide some info. The wife and I cam across this in Fahnestock State Park a few miles in on one of their trails. I figure it must have been a truck from the size of the...
  15. MustangMike

    My Masterminded 362

    So my long awaited Mastermind Ported 362 C-M finally arrived home yesterday. Of course, it had to come when I was so busy I did not get to open the box till about 10pm, and then it rains this morning. Well it finally dried up a bit and I started her up and went across the street and put it in...
  16. MustangMike

    Just a Little Prayer

    I just got a call from my cousin in Fl, who informed me that my Aunt Gwen passed away today. She was 87 last month, so I guess she had a pretty good run. Growing up my parents both worked, so Aunt Gwen would come over some times and either make dinner or bake things, or both. One time my...
  17. MustangMike

    My Ported 046

    A little over a month ago I picked up an 046 from an AS member. I wanted a saw that was just a little meaner than my 044 to handle the big stuff. The saw needed some cleaning and minor stuff, but was in generally good condition, and had 175 psi compression. I added a dp muff cover, HD-2...
  18. MustangMike

    My New Saw - 044 #2 - I Think I Got Lucky

    It is not a secret that I think the 10 mm Stihl 044s are one of the best all around saws out there. So when I saw this 044 offered for sale on e-bay, I just had to ask the seller some questions. It was not listed as a 10 mm saw, and I don't think the seller knew the difference. I think he...
  19. MustangMike

    046 Issue

    I recently acquired a used 046. The saw needed a good cleaning up and some minor parts, but is generally in good condition. The compression feels very good, the saw starts easily, idles well and even cuts well (my brother says it cuts just as strong as his 460, both have dual port muffler...
  20. MustangMike

    MS 460 Questions

    My Brother has a MS - 460 (2005?) that I would like to improve like I did with my 044 (less restrictive air filter and duel port muffler cover). 1) His saw has the adjustment restricted on the carb, so I know I have to remove the restricter, but how do you do it? Do you just pull out the High...
Back
Top