Search results

Neighbor brought me a TB PW to fix. I know nothing about these pumps. Engine is Briggs 11P702 dated 2013. I can't find a model # on PW. I first disassembled and cleaned carb in the USC but it looked good inside. Doubt I needed to do it. Symptoms - Engine starts and runs for 1 sec. Then rope is...

I was given this saw and it's driving me nuts. Cleaned carb with 5x 8 min cycles in USC. New gaskets, diaphragms and needle. Tunes in pretty well on H, L and Idle. It will start easily and run great for 30 secs, then leans out and dies. Can repeat this multiple times. I did not remove the...

From pics I've seen, the oil plunger seems too long for a plain Bantam. Could have been changed, tho. Anyone see anything to make this other than a Bantam - no suffix? On Acres, all suffix saws start in 1960 and newer. Thanks, Doug

Craftsman 358362180 / Redmax GZ4000. 18“ OEM A041 bar 3/8LP chain 62 DL Got this saw as a trade in. P&C were rough from probable leaky intake seal - lean running. Installed a McCulloch 4018 P&C with Base Gasket Delete. Adapted a Chinese 45cc carb to run saw as non-strato with non strato...

Got this saw in a trade in. I'm thinking it looks Mac-ish but see Made in Japan. Kioritz-Echo?

Early Stihl 026 w/ 18“ Rollomatic E Bar & Chain Bought this saw off a farmer lady who knew no history. Serial # 227341763 150 PSI. Starts easily. Runs and Revs. Oiler oozes. What I did: 1. Drilled tank hole to accept larger, newer fuel line and installed line. 2. Cleaned and rb kit in WT-194 but...

Anybody ID this model Shindaiwa? https://huntsville.craigslist.org/tls/d/owens-cross-roads-shindaiwa-chain-saw/6840088391.htm

Fellow brings me this blower cuz won't run. The bracket holding the coil is cracked off. Coil & flywheel have grooves where they have been rubbing a while. Is it worth it to pull the clamshell off and install a new one? I've never worked on one, so it'd take me forever. Does anyone have an IPL...

I got a 590 and am trying to look up parts. Where would serial # be? Other labels are good: EPA shows Aug 2016. UL sticker. Timber Wolf CS-590. Echo on clutch cover and recoil.

Fellow brings me this saw to fix in a box of parts. Never worked on one. Missing some parts - one is brake flag bushing. Does it have internal threads? All I have is a smooth ~7mm hole in the crankcase. Or is bushing a self tapper? Thanks.

One pawl, pin and spring went somewhere. And those 3 parts seem to cost as much as a good used flywheel. 503594602. Thanks, Doug Got one from Howard. Thanks

Fellow brings me a non-oiling 350. It was the worm gear buggered up. Putting it back together, the bar plate stands off on carb side. See pics. Looks like he may have caulked the channel where bar plate should go. I can't tighten the hex nut cuz bar plate pushes hard on worm gear. I couldn't see...

I bought a generic Chinese 272 top end a year ago and put on the shelf. Open today and see this. What factory would this be?

Got an 026 with a bent carb screw. Looking for a replacement. IPL shows 1121 122 6600. The 038 021 023 025 saws call for 1125 122 6600. The 1121 screw costs 3-4x what an 1125 costs. What's the difference?

I have a Poulan 2000 with too much oil shooting out. Is the Check Valve Duckbill behind the screen probably blown open? Easiest fix is grind off collar, remove screen and install new duckbill?

I'm rehabbing an 034 and some parts were in a box. Unsure about muffler. 2 nuts at top secure front plate to muff body but there are no nuts for bottom 2 holes. Seems like mucho exhaust would escape down there. Just add 2 M5 nuts on bottom? Is this correct order?....Cooling plate - flange -...

I've got a few A061, A018, A218, A318 bars - 10"18". Need a Large mount Stihl D025 18-20", prefer 3/8 .050. I can trade 2-3 bars for 1 D025.

I got an 034 with a toasted top end. I’m going with a 48mm bore 036 top end. 034 has Zama C3A-S19 carb. Is performance better with change to S39A carb? Thanks.

https://huntsville.craigslist.org/grd/6183214091.html Now, bear in mind that the ad is for the unwashed public - not you guys. LOL Compression feels real good, manual oiler works, will need sprocket soon, half a pull hot starts, ran so good that I didn't open up the Walbro HDB. I can ship to...

I get an MS210 with a trashed engine. Rebuilt saw with an MS250. Hey! Why is worm gear rod hitting tabs at the top and missing bottom tabs by 1/4"???? Take back apart and find new clamshell cap depression holes to sit on chassis tubes are too small. Engine doesn't seat. I re-did with OEM cap...