Search results

ill tell ya what, i think this new format ****ing sucks. i gave it several weeks, and its still way worse than it was on the old format. im sure @Darin had reasons, but this new format is ****ing trash. please vote your conscience.

Good shape 288, randy did it a couple years ago. Maybe 10 tanks of fuel through it since then. Bought it from a county garage, seems to have not been used much. When i got it a couple spring av’s were broken so i replaced them all with aftermarket hard rubber ones. Added the seventh mount, outer...

have this clean echo cs 370, appears to have been run on last years gas. was owned by an old guy at the country club where i used to work, doubt its been used 5 times. intake side looks clean, exhaust side shows scoring, saw is complete except muffler studs. comes with a bunch of other stuff i...

Sorry for the blurry pics as usual. Some 261/262 parts some will fit 254 and 257 as well. Intake setup w carb screws and hda120 (condition unknown), filter holder has the grommet on it. Has a full set of av’s, also a new aftermarket 3 shoe clutch and an oem 3 shoe clutch spider and spring. Good...

Lookin for an AF cover for a 395. Faded/a little rough is fine (actaully preferable) just want intact with no big cracks or chunks missing. Thanks

Wpuld like to sell this NOS KS top end kit. Complete with cylinder, piston, ring, bearing, wrist pin amd clips. There is one tiny little void in roof of exhaust port, not close enough or big enough to be a concern, but worth mentioning. $180 shipped

so a friend of mine has this stump from a walnut tree and wants to cut some slabs. Whats the best way to maximize this stump? He was thinking crosscut everything, it seems like that will lose a lot of the cool grain in the stump. This will all be done freehand. What say the experts?

NOS bare side cover for 272. Cracked near the rear part. $25 shipped lower 48 SOLD Decent KS 262 cylinder, i cleaned it a bit, still a couple little lines that can be just barely felt, also a small chip in plating shown with the pick $30 shipped lower 48

have some .058 stuff i dont use, first is a d009 techlite bar, 3/8 pitch, 72 dl. only used a couple tanks, with a lightly used chain. $50 shipped, a little more if way out west. Second bar is k095, 3/8" 60 dl. $30 shipped same as above. Also one new 73lgx chain 72 drivers. (2 of the chains...

Stopped by a friends house to look at his non-running 395xp. A quick once over showed no spark. Took off starter and coil was loose, both screws backed all the way out. Obvious signs of contact on coil and flywheel, but ive seen a lot worse. Reinstalled coil w proper airgap, amd still no...

Have an 028 super im working on, the pto side seal is leaking. At least it looks that way at first, actually it seams to be leaking around the outside of the race where the seal is pushed into the bearing. Ive never had one of these apart and im having trouble visualizing how its actually...

Have an 028 that needs seals. I know ill have to order a flywheel side. An old ipl i found shows 028 pto seal has dimensions 15x29.5x4. I have seals for an 034 i though i needed, an ipl infound shows that seal has dimensions of 15x29.6x4. Different part #s but seems like it ought to fit.

Doesnt need to be minty, just whole. Thanks

All n.o.s, filter and clamp still available from dealer, but not the elbow. Should fit other saws in the series but im not 100% $50 shipped in usa

Nos sweden-made complete starter and oem 272 decal. $55 shipped.

029 super in nice shape with OEM 039 cylinder/meteor piston. Cylinder has a few VERY small nicks in plating, that were blended a bit prior to assembly. Pto bearing on this saw failed and toasted its original top end. New FAG crank bearings, oem seals, fuel and implulse lines and rear bar...

Bought a lot of old stock parts for a couple items and really dont need the rest. Ill post a pic up this afternoon. Consists of a lot of springs, washers, gaskets, o-rings, a few condensors and points parts, some seals and rubber parts. it came stuffed into a medium flat rate box. Any...

Bought this saw last summer, have run less than half a tank of fuel through it. Was told when i got it that its a very low hour saw and i believe it, it is very clean in and out. P+C are pristine when viewed through exhaust. Compression right at 150, with base gasket still. HDA120 carb. top...

1 nos complete starter $50 1 decent used 272 top cover $30- sailed 1 nos bare bones clutch cover $35 1 decent used complete chainbrake$35-sailed 1 decent used 272 cylinder $35-sailed

Parting out an 028 super that was a pretty lightly used homeowner saw that appears to have been straight gassed. made in usa saw. top handle was badly bent at one point and all a/vs and fuel tank are tweaked as a result. cylinder cleaned up pretty well, but i got through the plating right at...