Search results

All stock jred 2166 and a 20" or 24" bar for Christmas 🎅. Saw works as it should and is in great condition. The sticker fell off the bottom after moving it during the pictures, but I think I saved it. Powerhead only 650 plus shipping. Thanks for looking guys.

Been a while since I done this, so I hope I'm doing it all right, I don't... 😆. I've got a 359 that I haven't ran in a bit. Last time I had it out it acted up and I shut her down. My guess is the carb needs the typical fix on these, if your not familiar I'll get a video link. It's also missing...

Just as the title says, 346ne in stock form. $425 PHO plus shipping. Pics coming shortly.

Great running Dolmar 5105 with heated handles. Saw is in good condition and starts, runs and cuts well. $400 power head only plus shipping. Thanks for looking guys.

As the title says I'm selling a ported 372 xtorq with huge dogs lol. It was ported by a faller who does his own saw work/builds by the name of Shawn Borsma(it has his initials on the air filter cover, I said it was for Super Brett :p. I'm not sure what his username is, but he's still around if...

Good evening guy. I have a nice 7910 that I'm going to let go to help with fund my barn build. It can be sold with or without the heated handle parts, if you are interested in just the heated handle parts let me know as well in case it doesn't sell with them. The parts I have are the handlebar...

Story goes like this; I bought a 2171 with heat that had been ported by Randy, a buddy of mine in said he wanted it, I told him if I find a nice 372xpg I'd swap it out and sell it, found one two weeks later lol. I pulled the cylinder and replaced it with the like new cylinder off the 372 and put...

XS ported 572xp with only a couple tanks thru it. The original owner decided he'd rather have a ported 60cc saw so I helped set him up with a pretty 357 and he had it ported by Kevin also. He also added a 395 decomp to make it a bit easier to pull over, it will come with both the 395 and the 572...

Grabbed this up with the intention of getting it going to mill a large white oak at my parents place. As so often happens another saw happened to pop up that was less of a project for me so this one is heading down the road. The saw is in no way a pretty saw, but it is all orange or some flavor...

Great running saw that runs like the fresh build it is. I've ran a few tanks thru this one and she pulls great, sure to get stronger as it gets broke in. It has a 390/wide clutch cover and does a great job moving chips. If I'm not mistaken the chassis is a 2018 and it had new bearings installed...

Here's a great running 346xp oe(the early version). I just ran a tank of fuel through it yesterday and it did a great job on everything I asked it to do. $325 PHO plus shipping net to me PayPal preferred. Here's a video of it running in black locust with an 18x325 B&C round filed. Pics in a few...

Husky 576xp with base gasket delete and a muffler mod with around 10 tanks. This saw had a defective decomp(now plugged), it was caught before too much damage was done. The ring's were replaced with cabers because there was a light mark on them as a precautionary measure and there was a spot on...

Nib husky 572xp PHO. Can add a total/tsumara bar and a husky h47 chain for another $100 or a jred labeled bar and an Oregon chain for another 50. Pictures of box coming soon lol.

As the title states I have a 661 with very little run time on it. Saw has a DOM of 05/18 which makes it the version 3 or the latest version as far as I'm aware(please correct me if I'm wrong on this). There is an "X" next to the serial number that I've read means it was a saw that had been...

Just as the title says I have a jred 2145 with a ported 346 aftermarket cylinder on it. The saw is in good overall condition and runs great. I've primarily used it for cutting pine/spruce to keep my other saws cleaner. It has pitch on the rear handle in the pictures but that has since been...

I have another 2166 here that has the "R" on the tank for refurbished. It has had the transfers ground making it perform just like the 2172/372. The squish has also been set at .020", which will make it a run a bit better than a 2172/372, the saw was run after the mods were done and is running...

Always something coming thru here and the best light is here in the kitchen. So far today I've had the 365XT with the transfers ground and a 372XT.

I have another 2166 here that has the "R" on the tank for refurbished. It has had the transfers ground making it perform just like the 2172. The squish has also been set at .020 and the muffler has been opened up under the deflector. Saw was run after the mods were done and is running well, I'll...

Another 2166 here that has the "R" on the tank for refurbished. I looked it over pretty good and I don't see any evidence that it's been ran before, it does have a few scratches and a crack in the clutch cover(I driller the end of the crack so it won't spread) from being handled/shipped. I can...

Recently acquired Husqvarna 262xp, if I used a 60cc saw much I'd keep it, but I rarely do so... It's a good looking saw and fires up and cuts well. It has the HDA120, sorry guys, there is one in the trading post for sale :). As far as needs I see it needs a new gas cap, unsure of any other...