Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. W

    Homelite 1050 super paint

    Yes. 2K is supposed to be really good. It is what Leon used on some of his Homelite resto's. You can also get clear in rattlecans for top coating Engine enamel. Sent from my LGLS775 using Tapatalk
  2. W

    Homelite 1050 super paint

    Boomer, just remember any rattlecan you choose probably won't be gas resistant. You will need a gas resistant clear over top. Sent from my LGLS775 using Tapatalk
  3. W

    Homelite ez automatic...

    You can normally buy all the linkage with brackets for the decomp on ebay for $12 in excellent shape. I had to buy set for mine. Sent from my LGLS775 using Tapatalk
  4. W

    Want to Sell Super xls

    If he doesn't take the red one I will. Sent from my LGLS775 using Tapatalk
  5. W

    stihl 025

    Not in the service manual. Very strange. I believe 7 to 10 thou is the average. Someone else can jump in if they know for sure. Sent from my LGLS775 using Tapatalk
  6. W

    stihl 025

    Have too look it up in the service manual. I will Post back later. Sent from my LGLS775 using Tapatalk
  7. W

    stihl 025

    Put the new rings in the bore and push them down a little. Usually with the piston. You can measure the ring end gap with feeler gauges. I've seen new AM rings that had almost zero gap to way to large a gap. Sent from my LGLS775 using Tapatalk
  8. W

    stihl 025

    Chris, did you check the ring end gap on the new rings? Sent from my LGLS775 using Tapatalk
  9. W

    still ms250 question

    If you used an After Market oil pump, that might be the problem. The last one I bought was undersized and went in too deep. It was too loose. So no way to use it. Put in an Oem Stihl pump and it fit fine. Sent from my LGLS775 using Tapatalk
  10. W

    Sold Homelite 410 Powerhead - Builder saw with scored piston

    Would someone please buy this saw. It's tempting me, but I have too many projects going on. I must resist. Sent from my LGLS775 using Tapatalk
  11. W

    025 dies immediately.

    Bedford is this the saw you did the video on? Did you ever put a correct tank vent on it.? If I remember correctly you used an AM carb on it. Some of these carbs work great but some fail. I've had pretty good luck with the one I'm running on my 021. Sent from my LGLS775 using Tapatalk
  12. W

    025 won't run. help

    What carb settings did you use? Sent from my LGLS775 using Tapatalk
  13. W

    Stihl 025 vent line fuel leak

    It doesn't look symmetrical in the pic. Do you mind taking it off and posting a pic. Either way the top grubb screw should be almost even with the top of the hose. Bottom grub screw doesn't look high enough. Not sure if that would make a difference or not. The OEM Stihl vent is about the...
  14. W

    038 magnum factory HP?

    Does the book list the HP for the 024? I've found one site listing them at 2.8 BHP. Not sure if it's accurate. Sent from my LGLS775 using Tapatalk
  15. W

    038 magnum factory HP?

    038 Mag. 4.828 BHP. According to the chart that Erik posted above. Sent from my LGLS775 using Tapatalk
  16. W

    Hand tools for fixing your saws?

    For working on Stihl chainsaws I like the t27 scrench that comes with the Kombi system. It's kinda like a T handle on steroids. The diameter of the shaft is too large for pulling cylinders, but it works great for everything else. Sent from my LGLS775 using Tapatalk
  17. W

    Stihl 036 issue

    Did you take the c clip off the stud that holds the chainbrake assembly, or is it missing.? Wouldn't cause your problem, but I wanted to make sure you had it. Sent from my LGLS775 using Tapatalk
  18. W

    brand new chainsaw wont fire a shot.

    Flywheel is $19, and the coil is about $6. Did you read the reviews on this saw? A common problem is they shipped with a bad coil. Sent from my LGLS775 using Tapatalk
  19. W

    Want to Buy STIHL 015 choke lever and air filter(s)

    The air filter you can get on ebay. $15 for oem, or $8 for homemade Max Flo. Sent from my LGLS775 using Tapatalk
  20. W

    Help with threads

    If you're using a mobile device with Tapatalk app, their is no way to change a for sale ad to sold. The tools aren't their at the top of the page. Sent from my LGLS775 using Tapatalk
Back
Top