Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Stihlmar

    Want to Buy 42 special parts

    Looking for a top cover. And possibly a tank/handle.
  2. Stihlmar

    Would you run it?

    Spins free. If I hold the rod to 1 side and use a small pick I can spin the bearing without any real catches or hard spots. Tried it on both sides. Just not sure if it got that hot or is factory coloring??? Saw was in a box in pieces. Reason it was tore apart was the rings stuck...
  3. Stihlmar

    Same 2 ported saws. 2 different sounds

    Just a random thought for today.... I have 2 - 026's. Both are ported but have 2 completely different sounds. The one that is quieter and doesn't really bark is a later 026 black lever. It has everything done to it the other one does except the muffler is slightly more opened up. But not...
  4. Stihlmar

    Who has the best 2 series husky junk pile?

    Hate to do it here but I am looking for 61-272 parts. Who has been hoarding? Not picky just needing to finish a project. Top covers. Grey or any other model that will fit. I'll make I work. Clutch cover. Pm me or point me in the direction of somebody. Just looking for some decent...
  5. Stihlmar

    61 to 272 parts kit?

    Picked up a $20 white top 61 that appears to have little use. Little scoring on piston exhaust side. So new lung is in order! Got it to run but not real well. Tore apart to clean and replace rubber bits. I purchased the 272 cylinder kit from hutzl. It's cheap and the saw was cheap. Why not...
  6. Stihlmar

    Loose heli-coiled plug

    Any advice out there for fixing a heli-coiled spark plug that's loose? Plug is tight in the coil but helicoil is loose in the cylinder. Was going to try and vac test the saw but even before tear down was done. Turned it over and heard it hissing. I would assume that would cause it to...
  7. Stihlmar

    Cut some cookies

    Just re-ringed the 026. Found a new set in a box of parts and figured, why not. It ran fine just noticed it didn't pull quite like dads so if nothing else. It was good practice. Widened the ports and played with the degree wheel a bit while it was apart. Just got the 5100 back from...
  8. Stihlmar

    026 numbers

    I am sure everybody is tired of the "porting for dummies" threads. I feel I have a decent understand of it but would like a set of stock numbers. With the exception of the various jugs from the years. What might a stock 026 jug numbers look like? Timing and or duration. Assuming somebody...
  9. Stihlmar

    What might this be?

    Anybody know what this thing might be? Make model year ???
  10. Stihlmar

    Barracuda is back!

    So my grandfather stops by my garage a couple times a week. I am always out there tinkering and enjoying the wood heat. I have recently been practicing and attempting my own port work. A few weeks back grandpa comes over and I was just finishing up putting my 026 back together. I fired it...
  11. Stihlmar

    Dolmar parts????

    Iowa boy here. Anybody got advice on parts for a dolmar 5100s? Took saw apart to figure out erratic Reving and poor performance. Found a few issue that were fixable. Looks like intake boot had a few puncture holes in it. So I need intake boot and another line. Would be interested in a few...
  12. Stihlmar

    5100s erratic rev no power at wot

    Hey everybody. Been following some of you for awhile now. Watching/learning. Just joined. Got a dolly 5100s awhile ago. Fairly low hours. Muff modded and limiters removed. Seems to erratic rev very harsh at no load wot. When in cut seems to lack power. Occasionally comes out of it and runs...
Back
Top