Search results

Hey Guys, Got an issue with a couple saws, both 250 's. They sat most of the summer and when they were got out to use, they stumbled off idle. Dried out from sitting I"m guessing. So I put a kit in both like I usually do, and now they start and run decent but don,t really change much when I...

I ended up puting one of the Baileys dp mufflers on for a quick one. havnt had a chance to build one yet.. it works well for almost no effort. cant wait to build one!

I had a guy tell me once that he used cam II race fuel because it supposedly didnt go bad. Dont know if its true but thats what he said.

that looks sharp woodyman!

sure, makes sense. if u take each wire and lay them side by side next to each other, thats the amount of blockage they would have. lot more than a guy would think!

Well that sounds like a good plan! whats the worst that could happen! Have to buy a new muffler OR a new saw! BUMMER!Been thinkin bout a 660! I know the 440 is way to restricted so im sure i will do something with it eventually. Ive been messin with the 044 because i run it everyday and...

I did remove the screen when i had it apart and re-tuned the carb for now. So u think its to small still? oakie doakie! Bigger it is! I would kinda like to build some kick butt lookin one when i have some time. i saw some NEAT:msp_love: ones on here!

Sorry Bounty Hunter I enjoy readin, writin' not so much! I guess what i was tryin to say was the 044 muffler had a hole in it already the size it should be. By my math anyway! (math is always up for debate!) Heres what I figured. exhaust port 1.125" X .750"= .84" x .8(80%)=.672" hole, does...

Ok so I have been readin up on cuttin up a muffler for my 044 but i have a question. It has a fairly large exhaust hole in it already(roughly .720"). Seems to me that goin by the 80% rule, that i'm already at full size. My 440 on the other hand has a SMALL exhaust hole in it and maybe that...

It is a 1979ish ford Industrial 172 4 cyl. I was trying to stay away from a rebuild because of chasing down parts and if a guy could swap it out easy enough i would do that. Im sure the motor is a mess so im tryin to figure out a upgrade.

It may need more than just head work, I was just hopin' for guides. I think it would be easier to find a different motor, but one with a PTO I'm not sure about. Just lookin for a ford guru that may be able to tell me about it. Seems I find a lot of stuff for an 8N that SHOULD fit but who wants...

Last fall I purchased a Asplundah Chipper 12" I believe. After I got it home come to find out there was no air filter in the filter housing. I have put about 20 hours on it and it goes through about a gallon of oil an hour and a set of plugs every 10-15 hours. I think I would like to put a...

Hey, thanks guys. I have the knives set to about .030". I have been in the field for the last couple of weeks so I haven't had a chance to use it. Ido greatly appriciate the info. Thanks again!

OK, That is the answer I was eexpecting and it makes perfect sense! I was pretty sure that was how it SHOULD be in there. I did check out the wear bar and 1 edge was new, 2 were slightly worn, and the one that was bein' used had about a 1/4 inch radius(very worn).I have been an industrial mech...

I didn't think I did a very good job of explaining it. You are correct about the adj. bolts and jam nuts under the blade. The blade has a replacable wear bar in it I don't know if it is supposed to face the in-feed or the chip chute. It bolts a spot in the blade that amounts to about2/3rds of...

It seemed to chip good, never really being around one it seemed ok. The small green stuff it bent up more than it 'chipped' so I figured it needed adjusted. It had about .200" clearace so I know it was needing adjusting. It just seems to me that you would want the support of the blade below and...

Ok guys, so I ended up buying the chipper I asked you all about. I have done a bunch of work to it and have gotten it running pretty darn good. ropensaddle thought it was a chipmunk. I used it for about 3 hours the other day and it ran great. Now that it is running good I pulled out the anvil to...

Simple. Thats what I kindof thought. I don't need anything to special, just something to keep from having to load brush into the dumptruck by hand. I don't mind loadin' the firewood size stuff, it stacks, and if it is decent hardwood I sell it as firewood. Since i am just startin' into the tree...

It has a 4 cyl. ford in it and if I remember correctly the drum is about 12 inches across. It does not seem to be a very big unit. Everything is free and turns. The guy has another chipper sittin' there with the 330 in it, but the radiator in it is empty and the oil pan is full(runnin' out the...

Hey guy's, I'll see if you can help me. I found a chipper about half an hour away from me. It is an Asplundh w/serial numbers of JEX9388. it has been sittin' for a while and it don't know much about it. I couldn't find a model or size on the machine. do the serial numbers mean anything to...