Search results

i have what you want

i have what you want

I have a Homelite 7-29 that will run but needs a coil. Does anyone have a good coil for it or advice on one that is the same or will work etc..............Thanks John

Bought my first Husky 51 in 94. Still runs great. Now I have 3. I cut about 15 cords / yr to feed the silver box out back.

Hi Folks, I got a Homelite 7-29 big boy. A friend was cleaning out a barn etc and now its in my hands. Fertilizer fell on the gas tank and handle and ate holes in both. Well, the bonus from that is the saw has low hours and good compression. I have not checked for spark yet. So, that said...

I like these guys, ask for Kyle. http://www.edgeandengine.com/

Aw come on its not that hard to get that carb out. Its probably not drawing fuel due to a cracked impulse line or a old carb diaphram that is rigid and not moving. It should have a Walbro carb model HDC (two different carbs on this model) go here...

Keep the flue pipe clean! I read this thread again. Going back to the fire going out; make sure your flue is clean of creosote. Mine gets very clogged up with creosote during the milder weather months due to the fire smoldering. In this case the stove does not 'breathe' well since its...

mahoning coal use I would also like to mention how i use anthracite coal in my MOF. Generally, I don't use coal unless the outside air temp is expected to be below 20 degrees F. In my stove, if I use coal I will put a piece of wood on the left and right side of the fire box and put coal...

How I run my mahoning mf300 Hello Folks, I have been running my Mahoning ODF since Oct 2008. I am very pleased with its service to date. I do burn wood and coal in the unit based on heat requirements, i.e. BTU's for the day. I do not cycle my grates. I set them so that the included bar...

Thanks Thanks for the input guys. Jacob J I'd greatly appreciate that info if you can find the time to check your saw. Thanks........J

thanks Lets hope so. I saw it run its nice. sounds like a snowmobile engine.

The final cut? As I understand it, the Pennsylvania Environmental Quality Board was the agency that put this rule through to passage. There is a 129 page document available for reading. I did not figure out how to link it here. I read most of it and it is a big compromise from what they...

My bud has a running SOLO TWIN. He needs a bar for it. He says its got a 404 sprocket. I know its a hard find but can anyone help him out with a bar? Thanks.............J

I have a runner That saw is rough. I have one that runs great. Check ebay for a piston/rings. I saw one there. Good lluck with it...........Mine runs strong but its ugly for sure. J

This thread is awesome Hi Guys, This thread is awesome for 650/750 owners. I have lots of them. . My 650 with the WB3 will outrun a 750 with a WB9. Its ugly but its mean. Man I need to cut wood..............Think spring............J

I've been reading that PA is now regulated as far as outdoor wood furnaces are concerned. After May 31, if you live in PA you will not be able to buy or install a new ODW furnace that does not meet the white lable EPA standard. From what I read so far, installed users will be exempt from the...

My Jreds 2 930's

Hi Fellas, I got a Wards WD-45 at a yard sale today. I can't find any info on it. Good compression with good bar and chain. Chain on backwards........Duh? Any suggestions for more info. Acresinternet has no info. Who made this saw? Thanks.........J

My OWB Temperature settings My stove is a Mahoning 300. For this time of year I have the turn on temp at near 140 deg F and it shuts down at about 165. When it gets much colder I'll tweek that to on at 155 and off at 175. What I've learned. When I load it in the morning I like to use...