Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. K

    Advanced log splitter plumbing question

    The blessings of voice dictation, although it's not too accurate and it does take a lot of typing to correct
  2. K

    Advanced log splitter plumbing question

    I have not read every reply in this thread so take this with the grain of salt -A dump valve is not to increase speed, but it's to decrease pressure drop so that a large volume of flow does not have to go back through the spool valve. It allows using a smaller (much cheaper) spool valve and...
  3. K

    Jred CS2145 questions

    Close. The name plate pictures were I saw I had access to the compare. The pictures of the bearings and seals were the parts out of this saw. I think ultimately it's a Frankenstein saw it's down the road and I hope I never see it again
  4. K

    Jred CS2145 questions

    Follow up, because it always bugs me to see a thread with the conclusion isn't posted So the bearings and rings 2245 fit. Saw back together, PV tested fine, onto its owner. I'm still not sure of the resolution whether parts were mismatched in a box whether the saw disassembled I got parts mixed...
  5. K

    Jred CS2145 questions

    I think you've nailed it. Looking in from the side of the saw that's a 2245, I'm seeing the same type of seals as I remember on the other one. It'll be a week until I get to the other saw but I think that's the issue It's a Frankenstein saw that really is a 2245 I'm going to order a set of...
  6. K

    Jred CS2145 questions

    I think you're onto something there. It is a Strato saw I'm not at the saw but I'll start looking at IPL's for a 2245 and see how that looks Here's what I have as a 2245 a different saw but I'll bet that's the issue Name tags are a different saw, crank case pictures are of this saw
  7. K

    Jred CS2145 questions

    So both the black tag and the starter cover have CS 2145. It is a full clamshell, doesn't have the half crank case at the bottom and the upper cylinder like a 350 does. Does not appear that the seals were butchered, but I'll try and get pictures of the crank case especially that which side has...
  8. K

    Jred CS2145 questions

    Bump Anybody have any info on this?
  9. K

    Variable displacement piston pump for splitter

    Couple other issues to think about. You'll need a close center valve, because most piston pumps don't work well with an open center valve. if they're at max flow at a very low pressure they tend to hammer out the pistons they need a couple hundred psi back pressure. Then if you use a close...
  10. K

    Jred CS2145 questions

    So I am fixing a Jred CS2145 saw for a favor for a friend. I am reminded why working on plastic cased clamshells is not cost effective nor pleasant. -Ordered some Cabers from the Greek. Got 42 mm. Went to assemble and it is 44 mm bore. Reordered rings, but question is How did it end up 44 mm...
  11. K

    Craigslist laughs

    Be more afraid that they vote and reproduce
  12. K

    Craigslist laughs

    So quite valuable must be one step below highly valuable?
  13. K

    fuel line in bulk or OEM replacement lines?

    A problem with online in general, and eBay in particular, is a lot of counterfeit parts. They have the OEM number, or tygon number, but they're China counterfeit so you don't know what you're getting. Might be a deal might be a counterfeit just don't know
  14. K

    MS 180C

    Tank vent? loosen the fuel cap so it can get air see if it runs for longer than a minute
  15. K

    New project saw: 026 Pro - couple of questions.

    I replaced the top end with the OEM but it was the 44.7. I've been told the 44 mm cylinders had better porting. Is there any truth to that and what are the differences? At my next rebuild I was gonna port and put the 44 back in. I did some work on a 44 mm on my sons saw and it turned out really...
  16. K

    Craigslist laughs

    I didn’t realize 044 saws were so valuable
  17. K

    Craigslist laughs

    The HVBW tree that grows everywhere.
  18. K

    Huskee 35 ton splitter pump...

    Is that a sealer or a structural adhesive? If it’s just a sealer, it may not have any mechanical strength or harden.
  19. K

    Huskee 35 ton splitter pump...

    Disassemble the pump and braze it? Or solder at a lower temperature maybe
Back
Top