Search results

Gaining on that route, I was hoping to find them with matching head styles bc of hating mismatched fastener heads. Will have to pull some from my other saws to get lengths as close as possible but will probably just have to run a nut on and trim off extra and clear threads with the nut

Bolts: Cylinder base bolts -4 Sprocket cover felling spike screw-1 Hand guard kick back lever side -2 Lower muffler support bracket bolts-2 Bar oiler plate screw-1 Handle bar bottom screw-2 Coil attachment bolts-2 Screw that goes into antivibe on tank-2 Recoil cover bolts-4 Top cover bolt-1...

Haha yea that's me. Can't fart in church and get away with it any more lol. Seeing you have a xpw in you sig line, yours should have a cover mounted tensioner screw, correct? This one has it in front the case, like a 2xx series would. Thinking its had some surgery done before. From the serial...

Have a oem 372xpw on its way to me in the mail, its missing the recoil assembly. Would like to be able to get a complete assembly that has the xpw sticker on it. Doesn't need to be spotless but readable would be nice. 4 bolts as well. Also would be in market for (2) kick back handles with the...

Wow those carbs are a pain in the nuts to get off after only dealing with older 372 and 046 style saws haha. Sawdust collected eveywhere so had to do external cleaning b4 getting carb out and afterwards. The air butterfly control body that is mounted above carb for the split intake had black...

spark screen is ok, light grey color, openings in center were similar to those on the edges. Are these a CAT muffler or a baffled can? Looking in from spark plug hole with light, the exhaust port doesn't have much carbon build up. Cylinder walls look good, I'd like to see some more oil sheen...

I decided to help a friend out that helps cut firewood with me on occasion just for something to do, by figuring out why his 445 is real doggy, at my cost since I sell the firewood, he just helps for free. It starts good and idles good once warmed up, but out of wood, when you accelerate it a...

28" on the butt after trimming 6" of flare off. Didn't measure further out but 24" bar was eating a full lunch. Black cherry. 3 10.5' logs. 50 logs within 100yd radius, hard+soft maple and b.cherry today, older stand, maple in the low wet ground had rotten butts but cleaned up once up hill into...

Worked out Well today. Only pain was that when I start walking out and am not past the tape it catches just enough to spring the hook loose, fine as long as I remember to draw it out some before I go. I may wrap it heavier there to make it stay out like a few of ya's have mentioned, definetly be...

Cracked my log tape yesterday when I released it and caught sideways between two logs, gave it a tug and pop it went. Caught the slack b4 it could unwind. Around 16" from hook. Racked my brain rest of day on how to fix for time being, thought I had small rivets but didn't. Ended up finding a...

Sorry about the x-torque tagging mistake, didn't mean for the confusion. Use both the 385 and 372 side by side and fingers go faster at times. I'll have to get boss's clearance to adjust the saw when we are finally able to get back in the woods after the snow settles down and we can get back...

The oem walbro doesn't resemble this at all. This is a pic of the China carb in both saws. Any ideas of what brand they copied for this? Walbro from oem is a rwj 050 stamped on side (rwj-5)?? I haven't taken out a China carb to see if any other stamps for indications.

My goal with this project is to teach myself how to bearings and case split, then get the top ends back to par. I think in box of parts there is a good oem 365 X-torque cylinder but bad piston. That may go on Chinese case and get a 372 top end for genuine 365 case.

I maybe off on the x torque part, I know the 372 is one and maybe why I'm thinking this is too. Its newer than 07 unless it's been tucked on a shelf. But my restart remedy so far with choke reset is just bc of tune issue and not a normal with these saws??. I have a personal 03 372 and it has...

Felling saw at work is a 385 xtorque, fairly new saw (i don't own it). Runs great but power/weight ratio I prefer my 372. Any who. Once this saw warms up it likes to die off at decel after cutting....like checking far side of face match up and having restart the sob. Does it both with laying...

When using a true-blue Husqvarna 365 stock carb, will it "flow enough" for the big bore? removing limiters of course I'd presume

Been hawking for a 365->372 project saw and found a buy on fb of two 365's and a parts box of a blown 365 xtorque (actual Husqvarna serial tag). I figured for price would work to patch up my old 372 of odd parts and then to be base for 365 build up project. Met the guy (he got the saws on...

X2...biting off quite a bit IMO, but dont know your situation. Forest soil may be good to grow trees, but for it to grow crops, thats differnt. gonna take alot of soil work and finishing to have a decent field. There must be farms or cleared lots already for sale for the state of the...

ok thanks, i'll give it a whirl

I have gotten the saw to idle correctly now (some may remeber my post from a couple weeks back)...ended up being i had a leak at the base because i didnt use enough gasket maker when i took out the base gasket. I also replaced the impulse line, but that looked to be in good condition, no dry...