Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. mtfallsmikey

    Vintage Chainsaw Collectors Lounge

    Wassup Buzz? Been a long time, how ya doin?
  2. mtfallsmikey

    Looking for info on water to air heat exchangers/hydronic forced air

    John Sigenthaler is the radiant guru. also suggest you look at Dan Holohan's books as well.
  3. mtfallsmikey

    Crazy Burls

    Woodturners would almost kill for a burl like that..
  4. mtfallsmikey

    Looking for info on water to air heat exchangers/hydronic forced air

    I used Heil hydro-coils, one on my oil furnace in my house, shop/garage has a stripped down gas furnace with blower in it, fan relay, hydro-coil. Heat loss calc for house was 46K BTU, coil I use is rated for 56K BTU @ 180 deg. water temp. At that water temp, I realistically get 120 deg. air out...
  5. mtfallsmikey

    Early blight in tomatoes

    Good article, thanks!
  6. mtfallsmikey

    How much Hp for a chainsaw mill

    Haven't been here for some time. Last time, you had sort of disappeared for a while, glad to see you back, I still apply some of your principles of chain sharpening.
  7. mtfallsmikey

    Early blight in tomatoes

    I let my big garden go fallow this year due to blight in the tomatoes, and potatoes, it is in the soil now, any suggestions as to how to get rid of it?
  8. mtfallsmikey

    Dipping into next season's supply!

    Burned 2 full tri-axle loads so car..
  9. mtfallsmikey

    New Pex

    What is the pipe size on that Urecon, 1 -1/2"?
  10. mtfallsmikey

    Found a brand new 460 but its too big.

    I like my short bar on my 460 for 2 reasons... better balance, and the majority of the wood I cut is 15-20". I can buck a log a lot quicker with that rig than anybody can with a 50 cc saw...
  11. mtfallsmikey

    HLsupply bearings questions

    Do you sell Save-Edge files?
  12. mtfallsmikey

    Found a brand new 460 but its too big.

    Have a 20" bar, RS chain on my 460... almost like having a hot saw.
  13. mtfallsmikey

    New Pex

    I used the Uponor pipe when I installed mine, 120' run, 2 deg. loss.
  14. mtfallsmikey

    Sprocket: To grease or not to grease?

    I squirt a lil Kroil on mine when I take the bar/chain off, or after sharpening. Blow out any krud w/air.
  15. mtfallsmikey

    Help with Central Boiler CL5036

    My controller still ok after 6 yrs., but might want to get a spare door solenoid to keep on hand, mine went out after 3 yrs. Keep it lubed up good, clean the crust off of the damer periodically
  16. mtfallsmikey

    Bonfire blues

    I like using a couple of old pallets for a base, then thick cardboard, then small dead limbs, build from there. My newest fave accelerant?... Mix of old cooking oil from turkey frying and diesel.
  17. mtfallsmikey

    firewood saw chains

    Save-Edge files are the best.
  18. mtfallsmikey

    Wood heat + central air in large house

    OWB? With a hydrocoil on the air handler(s)
  19. mtfallsmikey

    Gas tank crack repair

    What is good to use to repair a crack on a plastic gas chainsaw tank?
Back
Top