Search results

Ok i found the top off the 272 and it does fit. The hole i need to drill has been started, but im not exactly sure on how far i have to drill in. I really dont want to mess this carb up if i can help it. Will it help me to see if i take the top and the gasket off the carburetor? or, how would i...

Ok, and as far as the tops go what i need to do is get rid of the one with the 90 degree fitting for the impulse line, correct? Would it have the same effect if i closed the hole or would it be better to get the right top for it? edit: if the 272 tops fit then i should have 2 of them laying...

maybe it isn't, 8450540 is the serial number on the tag. I thought the first 2 numbers were year but could be wrong :help:

what exactly do you have? I think what i need is the piece between the intake and carb and the 2 carb bolts. I already have the intake piece that goes on the cylinder and the bolts and gasket for that(shown in pic). Almondgt- what is the difference between the 2 carburetor tops? And how...

The 630 jug is the one with the plastic intake. It also appears to not have an impulse fitting (i think thats what it is), the 630 mustve had the fitting in the case? There is no way the 625 boot will fit on that plastic piece because its too big around and too long.

I have what appears to be an 84 jonsered 625, when i got it it was showing over 160# compression. I pulled the jug off to inspect it and it had one small score in it, needless to say everything else is there and now i have a 630 dual ring piston and cylinder for it. It appears the 630 jug is a...

Any idea if the clutch covers are the same between the 625/630/670? I got a free 625 this week and all it needs is a clutch cover and bar/chain. Seems to run fine but i really cant tell until I get some load on it, has tons of compression!

Yup, it's a 2008 gsxr 600, everythings stock for now except the slip-on. If you look at the front of the saw you can see its been spray painted white, along with the clutch cover. Other than that, the saw is damn near perfect. It cuts really nice and has good power all the way through...

Hopefully the pics will be up soon(Thanks again Anthony!) and I will explain them a little better when I get back(I'm going over to my buddies to put the saw in some wood...)

Computer is telling me they are too big. I dont have an account on the image website either (can't even remember the name of it now...)

Picked it up today, came with a new air filter and a brand new chain still in the box. Only paid 400 bones for it! Runs like a top so far, piston/jug look good. I don't have any wood to put it in though :cry: Pictures in a little bit...

His ex-girlfriend is coming up from mass. today to help him start moving stuff out of his house, tomorrow he is coming down towards me a little and we are going to meet. Going up today was offered but he seemed to like monday better, I trust he will keep his word. All it takes to pull the...

Seller said he would hold it for me until I pick it up monday for those of you following the thread. :clap:

Thanks everyone, trust me I'm not doing this to be mean I just wanna keep it under wraps for now. Don't forget I'm probably the most anxious person here! :dizzy:

The seller has his price listed, but like I said I don't wanna give anything away.

AHH! I wanna show everyone but I really cant. You'll find out the details soon enough. :dizzy:

:greenchainsaw: There is a pic of it but I dont want everyone and their brother to try and buy it, I'll give you details after I find out if it's sold or pick it up, one or the other. Loose lips sink ships!

...if it was for sale, looked to be in good condition, runs good, 20" bar with spare chain, new air filter, and "hasn't been used much" (it doesn't look dirty at all, very nice looking). What would be a fair price? What would you pay for it? Thanks for any and all replies.

did you reset the idle screw to where it was?

I mix my gas with 10w-40, in the winter I use 5w-30. :monkey: