Search results

I have a Husqvarna 262 to rebuild. Are these aftermarket cylinder kits that Baileys sells of the same closed port design and produce the same high torque and power as the original oem's do? Does anyone have experience in the power comparison? Thanks, Stevie

A cracked rope rotor (pulley) with tend to do that. Stevie

Maybe someone can help me with a problem. I have a 257 and I bought the aftermarket 262 cylinder/piston from Baileys to put on it. It bolts right on no problem except it wouldn't pump gas. So I took the carb off and saw the problem. The pulse hole on the 262 cyl. is over to the side whereas the...

I assume you know that on that one the diaphram metal probe thing hooks into the inlet lever. It doesn't sit on top of it like most carbs do. Stevie

yes I do this all the time to set my carving saws up with 3/8 lo-pro. All I do is take a dremmel with any old grinding wheel and make a groove from the top of that 041 bar down to the oiler/pin hole. I do this on both sides so I can turn it over. That's all I do. It takes about 30 seconds to do...

Yes , the same sprocket is used for 3/8 and 3/8 lo-pro.

You have a lot of questions there. I am only going to hit on a couple as I can't even remember them all. GB is making 1/4 pitch rim sprockets and even Baileys sells them. So that is the way to set up for 1/4 pitch. Yes it will work so much better on the carving bars,even the quarter tip. There...

why? Why would you want the gov. to buy your chainsaw for you? Stevie

Recoil pulley, starter pulley, Pulley with the rope around it, whichever we call it, that one. Stevie

You don't prevent it. The pulley has a crack in it. It is broken. Get a new one. Stevie

Back when I worked in the shop I found this to be a common leak on these saws. I always packed the spacer with grease and it always worked. That is what the Stihl techs told me to do also. It's not really a matter of wear, Just metal against metal with nothing there to insure a seal. It doesn't...

service tool service tool part # is 530035560. Retail is about $5.50. This is actually a pretty good idea as they get out of putting on limiter caps. Anybody who can order a poulan part can get you one. If you can't find one I could mail you one. Thanks, Stevie Songer

Dave, that part# is 537069301. About $10. Stevie

I have had customers complain about the lack of oiling on the new Jonsered and Husvarna mid sized saws (346, 350, etc.). I run them and don't have a problem. But some do. Anyway, You can replace the oiler pump piston with the one that is for the 2159, 359 and it is supposed to increase oil...

I TOLD YOU I CAN'T HEAR!!! lol. Yes, I wore ear protection during the time I suffered hearing loss. I have worn ear protection from the beginning. StevIE

Huh? It could be just coincidence that the hearing went at the same time as running the saw. I don't know? It's not that it's that loud, it's just that same deep drone pitch ??? for several hours a day held up close to the body. StevIE

What about hearing damage? I have ran stock saws for the last 3 years, about 1000 hours per year. I wear good ear muffs. I have lost considerable hearing ability just using these stock saws. I would be interested in the mod saws if not for the increased noise. StevIE

The 2145 and the 345 are the brothers. The 2045 was the brother of the Husky 45. As were the 2050 and 49. Sales rep told me they originated from a Partner. Stevie

Where did you buy it where it is fresh out of the box and an empty tank. Didn't they service and adjust it? Stevie

Neither do you want the piston to be slick and shiney. That indicates wear. You want to see a cross-hatch pattern. Stevie