Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Stihl 361 Summer Maintenance

    Ok, here's a question for some of the guys that live in warmer climates than myself. I had my 361 out today doing some storm cleanup, and brought it back to clean it up when I noticed the recoil cover was all clogged up. I proceeded to remove it and continue my cleaning when I realized that...
  2. S

    Dodge 9.25 Rear Axle

    Does anyone have any info on a Dodge 9.25" rear axle, with limited slip in a 2002 Dodge Ram 1500?? A buddy of mine just grenaded his, and rebuilds are only $1100, but parts are in the neighborhood of $400. I've setup rear ends in the past, but always had a diagram or illustration to help. I...
  3. S

    Stihl 015 NLA Parts

    I was wondering if anyone has come up with a solution for the gas tank/oil tank cap seals for an 015 stihl. I got the sucker to run, but you can't turn it or gas will spill all over. Checking the oil cap its gasket is cracked too. Called my dealer and the part is NLA. Stihl part NO: 0000...
  4. S

    Stihl 015 Carb

    Does anyone have the initial carb settings for a stihl 015? It was passed down to me and it runs for about a minute then quits and will not refire until left set for 5min. I just put a carb kit and fuel filter in it and tried putting the H/L screws back to where they were and now it won't fire...
  5. S

    041 Vacuum specs

    So last week I finally got my 041 AV "Magnum" back together. Mild port, muffler mod, sans base-gasket, Super carb. Instead of a "here it is, it runs great" thread this is a "son-of-a-gun, thing won't run" thread". After toying with the carb and 2 kits I did a leakdown test on it, and it...
  6. S

    Honing ported cylinders, when?

    I have a cylinder that I would like to do some mild porting to. I don't have a hone, but would like it to be honed with the new rings I'll be installing. Would you hone before porting or after porting? Pros/cons with either way?
  7. S

    Tilly carb numbers

    Got another 041av, some people's kids I tell ya. Anyone know what saw had a Tilly HS181 on it? The only carb I've seen on an 041, av, super, fb, has been HS138. This 181 has a smaller venturi, and smaller neck feeding into the intake than a 138. Thanks in advance.
  8. S

    Carb swap, mid-sized stihls

    Anyone know if a larger carb will fit an 041?? Maybe an 038 or 044 carb? Or would it have to be from a "horizontal cylinder" model saw for the linkage to work? (056?)
  9. S

    How close to ground?

    I've been a long time firewood cutter, and have usually watched my father felling. Now that I'm starting to do more of the felling I have a question about where to start my "notch" and cut. I've seen people start at their waist, knee-high, or barely off the ground. Is there any advantage in...
  10. S

    Stihl 041AV Rebuild starts

    The crankcase halfs came apart but the bearing stayed on the crankshaft. I put my jaw puller on the bearing and and turned the bolt 2 full turns and then got scared when it didn't move. Is there a hot/cold process I could use? I'm working inside, but it's 10F outside. I don't need the bearing...
  11. S

    John Deere Q300F

    I am looking for any information on a John Deere Q300F chainsaw. A good friend of mine has entrusted me with fixing it's oiling (lack thereof) problem. Serial number is 077425M, and the tag also says: Made in China. Any info would be helpful.
  12. S

    Sugihara bars......dl count?

    I've been cutting for about a decade, mostly with my dad firewood cutting and on the side taking down neighbors trees. For some reason I'm harder on my saws that my dad is. :chainsawguy:(must be youth.......) I've torched or bent 3 bars on different saws in the past 2 years, all Stihl...
Back
Top