Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Want to Buy Echo CS670/680 Muffler

    Check your private messages .
  2. S

    Hit metal today-chain still usable?

    Del and HumBurner , to save a lot of round file strokes , I have used my raker file (round edge in the gullet) to file the hard chrome damaged top plate then use the proper round file to profile the gullet . It might take a few minutes but a lot less round filing and gullet over filing . Scott
  3. S

    Craftsman Chainsaw Blade Model # 917.353771 3.7 18"

    Hello Joe , George never gave me the part # on his Oregon bar . If you call Oregon customer service they will help you find a bar for your saw . Scott
  4. S

    Nik's Poulan Thread

    Hello Bob , I think that saw is a poulan 2400 made for sears/craftsman .
  5. S

    Keeping an Ash Round from Cracking?

    Hello StihlsawuserMS361 , I have used paper grocery bags and newspaper to slow dry the cross sections of Eastern red cedar and ambrosia stain red maple . Three layers of grocery bags or newspaper worked . Two years in the garage then one year in the house . Scott
  6. S

    Poulan 2375le Cylinder

    Did you also ditch the diffuser ?
  7. S

    Nik's Poulan Thread

    The oil pump is behind the clutch so remove clutch .
  8. S

    Poulan 2375le Cylinder

    Hello Chuck , your pictures show that you have the same muffler that the PP262 has with the heavy catalytic cage .When I private messaged you I thought you had the older aluminized muffler that had the 1/4" outlet on the back left side of the muffler . Later you mentioned the 1/4" hole was in...
  9. S

    Poulan 2375le Cylinder

    Your muffler sounds like the muffler that came on my pp4620 except mine has a factory 0.40" diameter center hole with two 0.125" holes . The additional muffler backing plate will guide more cooling air through the cylinder fins . If you will drill the three outlet holes to be about 5/16"...
  10. S

    Poulan 3700, worth fixing?

    I remember 8mm bar studs and the D176 bar mount .
  11. S

    What is it?

    The tag is behind the clutch cover .
  12. S

    I have a poulan pl3816 and want a bigger bar

    I'm curious , if you look at the epa sticker on your saw , does it have 42cc displacement ? Did the bad pinch mess up the sprocket , guide rails , twist the bar , bend the bar ? A relative has a poulan pl3816 and I remember it having a Oregon A041 mount bar .
  13. S

    Saw Chain Grinding Angles

    Hello Ol' Brian, it would help if you would state what chain you have been sharpening .
  14. S

    Poulan 3300 no fuel

    Different saw (2800) would be good to start a new thread .
  15. S

    MS 400 muffler

    What are you getting the 33% comparing 1" outlet to muffler displacement ?
  16. S

    Nik's Poulan Thread

    Ed if you'll scroll back to posts 36,317 and 36,318 they are discussing the carb settings for 5020 . Found it by searching 'PP5020 carb settings' in this forum .
  17. S

    Husqvarna 141 3/8LP or .325

    If I were cutting mostly hardwood then I'd use 3/8 low profile .
  18. S

    Circular Saw Attachment

    Hello Kevin , do you remember what rpm that 193 would run with a circle saw blade ?
  19. S

    Poulan 2000 rebuild not starting cold

    Did the carb gasket tear when you removed the carb ?
  20. S

    Poulan 2000 rebuild not starting cold

    Time to inspect the reed valve .
Back
Top