Search results

I rebuilt another grinder for myself, so I'm selling off my original RSII grinder. I replaced the bearings in the motor 4 years ago and I've only used up 1/4 of a stone since then, motor runs super quite. I also skim cut the stone arbor on the motor armature between centers so it has perfect run...

Husqvarna 395XP with very low hours. Still has sticker on bottom of tank and behind the air dam. Typical light melting on cylinder cover over muffler, slightly dented in over front AV mount (purely cosmetic), and missing the recoil decal. Otherwise in really good shape, completely stock, only...

Husqvarna 357 with crank stuffers removed and ported AM HyWay 359 cylinder. Built in the spring of last year, only has 1 tank through it since rebuild. Modified HDA carb, very large outlet modified muffler with screen, WC dual spikes, tunes out strong at 14k RPM. $400 PHO.

Extremely low hours Jonsered 2152C. This is the red headed better looking cousin of the Husqvarna 353. 52cc, full magnesium case, small spline replaceable sprocket with .325x7 rim. $300 PHO

This cylinder was on my personal 359 when the wrist pin bearing cage failed. I ordered a new cylinder and installed it before I thoroughly looked over this cylinder. The only damage was to the squish which I flattened out. It's had some other previous injuries (ring snagged plating above the ex...

NOS Stihl 066 flywheel/starter cover. $100 shipped to lower 48.

I did another run of chain holders. They are made of steel to last longer than the oe aluminum, tight tolerance to the chain to minimize rocking, 50/63 gauge. I can make 58 gauge as well. $55 a piece or $100 for a set. Chain stop paws for RSII, $25 for a set.

Recently rebuilt and ported Stihl 044 D chamber, 12mm pin. New OEM piston, new seals, fuel/impulse lines. Ported with reasonably quiet muffler mod. 3/4 wrap handle has been tig welded on the bottom left below the grip. Has 046 tank, carb and filter setup. $500 PHO.

This was my uncles 041 that he bought new before I was even born. He's always stored it in the case in his barn and didn't use it much as he also had a 028. As you can see in the pictures it's in great condition and will come with the case and 2 chains. Would make a great addition for someone...

One legendary saw for sale, guaranteed to earn you street cred amongst the old loggers as you jab with them while sipping a cold one after a long day of murdering trees. Just holding this saw reminds you of your days cutting old growth even though you've spent most of your life driving a...

I finally got some stickers made. Anyone who has a saw I've built who would like one please PM me.

This is a freshly rebuilt with new OEM bearings and seals, short 066 case with ported meteor top end, AM dual port muffler that has been modified. The original style flat top cylinder cover doesn't fit well over AM cylinder so it has been changed to a bubble top. New west coast style clutch...

Selling chain holders and chain stops. The chain holders should fit Silvey or Simington swing arm and Silvey RSII grinders. They are CNC cut from steel plate and are very tight tolerance to the chain to minimize rocking. Available in any combo of gauge. $100 set, $55 for one. The chains stops...

Just a few recent saves I actually photo documented. Stihl 660 that the big end of the rod got loose and tried to escape. Welded. And finished.

I have these bars/chains that I have no use for. Prices are without shipping. Starting from the top. The bars: 36", 63g Lg. Husky, Oregon, reground from 58g to 63g, rails have been ground, the tail is getting a little short, tip is in good shape. $40. 24", 58g Lg. Husky, Oregon in good shape...

Stihl 066, flat top none decomp cylinder, short 064 style case. I recently rebuilt and ported it, and put in new seals, rings, and fuel lines. The piston was in great shape, machine marks still visible across almost the whole skirt, bearings where like new. The bad... it was a tree crush victim...

Didn't get what you really wanted for Christmas? So return your unwanted gifts and purchase this freshly rebuilt and ported 394XP. It has new bearings, seals, meteor piston, fuel lines, fuel filter and air filter. The squish band was cut 0.030" for a mild compression bump but not too much to...

Nathans Silvey was in need of some attention so he dropped it in my garage to get a little work. I had to cut a couple of new adjustment studs since the others are bent and no longer give a linear adjustment. Also it was missing an adjustment knob so I found some others that are similar...

I have a few of these kits left to convert the Silvey RSII grinder to a bearing slide. More accurate and free sliding then the stock setup. $275 for the kit, it comes with what is shown and detailed installation instructions. Close up of the installed block and outer dust shields. Here...

Selling a Husqvarna 394XP. Recently rebuilt and ported. New starter ASM, seals, bearings, meteor piston, fuel lines, fuel filter and air filter installed. It has 0.050" cut out of the squish band, a dual outlet muffler with screens, and the WJ39 (non EPA) carb. 205 PSI compression and should...