Search results

Anyone know the initial l and h setting after kitting the carburetor? All I’m finding is take it to the dealer. I’ll throw it in a river if that’s the only option. :laugh:

Anyway to remove the caps on the screws without damaging the screws or an earlier version of this carb without the caps?

http://www.foxnews.com/auto/2018/04/11/hellcat-powered-ram-rebel-trx-set-to-be-most-powerful-pickup-ever-report-says.html Everyone needs a 700hp factory pickup truck.:)

https://www.google.com/amp/s/www.maxim.com/.amp/rides/return-of-the-hemi-cuda-2017-6

Is she beautiful or what?

New saw on the way, will a 272xp jug bolt on to the 2166? From what I've read there is a re-stricter cast into the 2166 that can be ground out but if that's the only difference in the jugs surely the 372 jug would bolt right on. What say the gurus?

Been having trouble with it. Took carb off today and cleaned it. I noticed the foam or rubber gasket that sits below the carb was gone. It needs that to run correctly am I right? Something to do with the pulse ?

Anyone know who has the best price on one of these?

Lost the chain tensioning screw and the clip in side the chain cover. Local dealer says he can't get the parts anymore. I'm 2nd shift and off to work but will reply tomorrow if anyone might have the parts. This saw still runs like a raped ape. Throwing away is not an option. Thanks Eric.

I guess I could settle for one of these. http://wot.motortrend.com/1407_2015_dodge_challenger_srt_hellcat_makes_astounding_707_hp_650_lb_ft.html

I've kitted this carb a number of times over the years and not had much problem but this last time it has been hard starting. if I take the air filter off and prime it starts right up. Does anyone know what the height of the tab should be set at that raises and lowers the needle? It's a...

It's mostly Osage orange and these trees came from a 25' radius, blown over and laying on each other. My dad never showed like he said he would so most of my time was spent hooking a chain on and dragging them out to where i could get the forks in the bucket under them to spread them out.:laugh:

Saw 08 Cummins 4x4 trucks yesterday at a dodge dealer marked down from $42,000 too $27,000. Dealer told me if I did not see the one I want he would find one for me. I may have to do this while mine is still low miles. Great time to buy.

My boy wont leave me alone about this car so I guess its time to paint and put it back together. It will be a while until he can drive it so I will have to drive it until then. :laugh: I have a new pair of the original b1 heads fully ported and a new stroker crank. Engine should make 8 to 900...

I used to know the name for these worms but have forgotten. About five years ago I planted 250 austrian pines around my property. Three years ago I found small worms eating the needels. I used orthene to kill them and two or three days after I spray I check the trees for live worms. I cant find...

Does any one know whats different between the 670, 670 super and 670 west coast? Were they all called champs or just certain models?

When I let off the throttle from full speed the engine is slow to idle down. I just kitted the carb and cleaned it,checked all the orfices and put a new fuel filter in the tank. If the reed valve is bad could that cause it to take to long to get back down to idle? I made sure the carb is tight...

e-mail with price if you have one.

How old is this saw? CC? looks pretty neat but weighs a ton. Was this a throw away saw?

Would it be legal to run this fuel in my saw. It looks like you can get it in 86 tru 118 octane. Leaded and unleaded. Seems like 90 or 91 octane should be ok. Dont know about the price though.