Search results

Hello All Would anybody have a copy of a RE107K parts manual?

Hello All Thanks for the feedback. I have just purchased two carbies. Turns out both the HT75 and FS85 take the same carby. Cost me about $12 each with free freight from China and they come with two spare primer bulbs.

Helllo Does any one have a manual for the concrete vibrator that fits onto a Stihl FS85? Thanks Phil

Hello All Has anybody tried some of the replacement carburetors on ebay that are a third of the price of genuine Stihl carbies? I am thinking of trying one in my little used HT75 pole saw and my FS85 brushcutter. They look the part in the pictures and I am pretty sure the genuine carby comes...

Hello Does anyone have a copy of the latest Stihl Special Tools manual? The one I have is dated 2011. Thanks in advance Phil

Hello All Would anyone have an IPL and or a service manual for an FS560CEM clearing saw? Thanks in advance Phil

I am not sure if that is correct at least not in every situation. On the old 041's with lined clutches. I have seen the clutch material come off and run steel on steel and still not break any springs. The clutches were traveling about 1.5mm more than they should. In my experience what breaks...

Pretty sure the 009L never had points. The label on Windwood's saw says "electronic" so there is no points in the saw. If that saw was mine the first step would be to confirm if it has spark. If it has then clean the carby if it has not then you need to find a replacement ignition module. They...

My mistake I should have looked closer and thought about it a bit more:) For some reason I had it in my head that both 18 and 19 were only gaskets but of course they are not. 18's the gasket and 19 is the suction chamber diaphragm which would explain why no fuel is getting through.

Glad to see you found something. I assume without the gasket there is/was not enough room for the little valves to open. Heres an 031 electronic flywheel on ebay When I replaced the points in mine I bought both a new flywheel and the genuine ignition from ebay. I have also had bad experiences...

You guys did read all of Tait's post, right? Even if the timing is out far enough that there is no kick or backfire or anything with the amount of pulling he has done so far there should be fuel in the carby. Also as Tait mentioned it will run briefly if fuel is poured down through the plug hole.

That sounds fine. I have seen it before where the prongs that the needle sits in are on top of the needle instead of in the groove. I have also seen the little needle stuck and the diaphragm is unable to unseat it. Another thing you might want to check is the pump diaprahm is on the correct...

I hate to state the obvious but did you make sure the needle valve is seated in the control lever correctly and/or stuck in its seat? As this saw has been sitting for a while did you remove the jets and make sure the ports are not blocked? Also there is a small mesh filter inside the carby that...

According to the manual it only say; It also goes on to say: Also check your ground lead. I have seen it happen before where when the plug lead is pulled out of position the ground lead works as intended but put the plug back in and the lead on the plug and the ground lead short circuits the...

Here's one on ebay I have seen a few of these with the screwdriver tip broken off. I think they made the screwdriver tip a little too hard. Although some of the one I have seen broken I suspect they were used to pry apart the bar groove after it had been pinched.

Sounds like the flywheel key has sheered off and the flywheel has turned on the crank thus putting the timing out. I have seen it a number of times on the 051 especially if the flywheel is refitted to a dirty or oily crank. Given that a small M5 nut in the system would most likely have caused a...

Thank you very much. Exactly what I was looking for. All I need now are the manuals for the MS382. Regards Phil

Hello All I am looking for an IPL for the MS661, MS382 and MS461 chainsaws and the FS560 clearing saw. Also if possible service manuals for them as well. Regards Phil

Hello Tim How far do you have to move the chain between tight and loose? If it a very short distance then you may have a sprocket with a mismatched chain. If it is a longer distance then it is probably nothing to worry about. Most bar and chain combos have a tight spot especially if they have...

Early model 042's have very little in common even with the 048. There are a few smaller parts on the 042 that were also used on the 028 and 038 but they are the more common items such as trigger mechanism etc. The oil pump is used on the MS380 and MS381 as well but I am not sure if they were...