Search results

Saw was locked up. I got the cylinder off, but it will need a piston and cylinder. Saw is complete even though the pics don’t show it. PHO $180 Shipped east of the Mississippi.

Efco Chain Grinder in good condition. I do not have a grinding wheel for unfortunately. It has the reversible motor switch as shown in the photo. Has the tilt adjustment that some chains have. $200 shipped to the lower 48. The fan shroud is cracked, but does not affect operation. Let me know if...

Like the title says, I’m looking for an 084 top cover. The uglier the better. I’d prefer it just not have cracks or burned. Thanks!

Husqvarna 288xp non decomp that starts, runs, and oils as it should. All original Husqvarna parts and fasteners. Very solid saw for its age. Let me know if you’d like more pics or have any questions. $400 PHO plus shipping. The video is a couple cuts in three year old cherry.

Looking to sell my battery charger that uses a McCulloch 10-10 power head as a power unit. This is a Lear brand name battery charger that charges 12, and 24 volt electrical systems. It starts, runs and charges like it should. All it needs is cleaned up a little. $200 plus actual shipping. Sent...

Need a muffler. Have paypal ready.

Well, I am no collector and thought these may do a collector more good than they are doing me. NOS Poulan 330 With Bar and chain never unboxed. $225 plus shipping. Poulan 3400 fires with a shot of gas down the throat. Will need the fuel system gone through. $100 shipped to the lower 48. I...

I need someone around, or near Boyertown, PA willing to pickup and pay for a saw, and then ship it to me here in East, TN. I will gladly pay for your time and trouble. If interested, just shoot me a PM. TIA

Like the title says, I need a Poulan 8500 crank case. The models that will work are a 6900, 7700, or an 8500. I have things to trade or cash. TIA!

I have an HT75 pole saw here and I cant get it to oil. There is a really good reason for this too. When I got it the oil cap was missing and the oil reservoir was half full of sawdust. All I have done so far is take the reservoir off and clean it out real well, and clean the pickup and pickup...

Can you bolt a 390 top end on a 290 bottom end, or do you need a 390 crank, bearing cup, etc.? I searched for a while but never found this exact question. TIA!

I am in need of a couple 3/8" three rivet bar tips. My question is does bar length matter? A couple adds I've seen show for bars 24" or less only, and my bars are 28", and 36". I assumed a three rivet tip was three rivet tip, and would fit any three rivet bar. This will be easy for someone. TIA!

I have a friends 029 here and it was out of tune, but the main reason he brought it to me was to check and odd noise that is going on. Well I tuned the saw first naturally, but the noise I cannot figure out. It is a chatter like a crank bearing is going bad. I removed the sprocket and the recoil...

I recently lucked up and was able to buy a Dolmar 166. I am about to have it ready to use and have been looking to buy a panther mill II to do some chainsaw milling. I have searched, but can't seem to find how to choose a mill length based off of bar length. It has 36" of usable bar past the...

I have a guy bringing me a stihl HT101 pole saw and says the shaft is bent. I have called two dealers and both said I wanted nothing to do with taking the shaft apart, that it would be better to just buy the whole shaft assembly. Both dealers also said their mechanics had to go through a special...

On a fluke I found an old Poulan and Sachs Dolmar dealer recently and went back today to take a look around. Here is what I came up with. The guy was very fair I thought and I will probably go back, but the big highlights for me were all the NOS parts and saws I got. Sorry bout the blurry pics...

Just wondering what you dealer types, or you guys that buy them several at a time use. Which ones filter well, but flow well enough for the big gas hogs or ported saws. If you have a couple you use, such as up to a certain size you use X filter, and then after that size use a Y filter. TIA

This looked like a deal to me. What do you guys think? Local craigslist ad. Wood Splitter Parts: Vertical 6" beam with large foot welded on bottom Sliding splitter head Hand controls Pump 3" X 24" cylinder All parts are unused and ready for you to build your own heavy duty wood splitter.

I need something to skid logs with to get them to where I can split and haul them for firewood. The primary machine I will be using is a 756 Farmall tractor with a boom pole. I will also be using a smaller garden tractor with a three point ball hitch attachment from time to time. My question is...

I have a North Star 30-ton wood splitter. It is tow-able now but 45mph is as fast as you can tow it. I have been thinking about getting a set of rubber torsion axles and bigger hubs and wheels so I can tow it up to 65mph. The axles have been warm to the touch a couple times and this just worries...