Search results

Mega Maul with steel handleis a good choich it looks like the Sotz,and weighs in at 14.5 pounds. I like The ChopperII,even though it does get stuck in the wood,sometimes.Usually I'll use a splitting wedge,in the knotty logs because I don't have a splitter,yet.

Glad you still have all your toes,not to late for safety protection,they say a dull chain can tear more,thus doing more damage.Either way kevlar boot is better than leather.

I am going to try spraying some carb cleaner on there,and check for some leaks!I got some fresh gas,but after sitting for 9 months I guess some stuff can get stirred up,maybe have a clogged fuel filter,hope it is something simple.Someone once told me to "make sure all the bolts and things are...

The idling is getting smoother,and no more backfiring,after a 15 mile test drive after a warm up,and then it wanted to die,and did start dying at low speeds,example:when it was at a stop sign,it died,but when running at 35 ran normal,then turned into driveway ,it died before I could park,then...

IT starts easy,but then idles high,and a little rough when driving at low speed,and it had a little backfire through the carb.

I decided to fill it with 10w-40.I added about 3 quarts by the time it came up to the full level,which tells me it still had about a quart of some "unknown"fluid left in the case.A good thing because,breaking parts is a PITA.And then after checking the rear differential,it too was very low,I put...

You too!

Sometime before I was born,I don't know.

I am going with what I like,not naming brands,just as a clue ,think of two big names, saws trucks,and so on,and it is one way or another,I try both and pick the best,whatever I happen to prefer or enjoy more,so oh well if you like what I like ,or something else, they are both o.k.Only thing is...

Won't start Only a quarter mile to grandmas and what could it be? To make the long story short,pulled the starter out,to it to the autoparts store,and oh,yeah.The starter went out,how did it cause the truck to die, I don't know,but that's what happened,and the nice thing about about old truck...

Pt. Two. And then ,there was the second hill coming up,so I pulled over to let some of the vehicles fly by,as we wern't making such good progress uphill.And we continued on.So this time I said ,come on Betsy,and passenger and I patted dashboard,as I downshifted the auto trans into 2nd and...

To:Uncle John, ft.churchill ,and Overtrained,Thanks for your help. Well, after a friend came by and all of the great advise,my truck is on the road,again! It took a little while,by 3:00 pm we were on the road,had a few tense moments ,cranking the engine,with no start and almost draining the...

Squared away ! I know it's late, but got it all squared away with all of your help.Thanks.:rock:

I'll keep trying!

Thanks alot I am out working on it,have a friend helping,so I'll get back here later and let you know how it's going. I think the rotor was pointing the opposite way.

rotor question Should the rotor point to the#1 cylinder,or the #1 plug in the cap?

Any one like the old full time 4x4?It's a 203,I think?Getting my wood hauler ready to go. Checked the oil in the filler hole,it supposed to be a half inch down when full , and put in two quarts already,and still not full! And it isn't leaking at all. Should I keeping adding oil,and just hope it...

So if I am off by a tooth,or off by 180 degees ,just take it out and start over by going to TDC then reinstall,and check plug/wire fireing order,and turn oil pump,if needed,just about got it I think.

I have the HEI,but didn't remove the wire.And haven't used the breaker bar to turn it yet,first thing tomorrow,will give it a try,and compare to diagram. Working on it in the driveway,20 degrees outside.