Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Makita EA4300F Dolmar 421 Oiling Question/Problem

    .325 bars have a larger radius nose then 3/8lp, has everything to do with chain throwing. in his first post he said he did set the oiler to max.
  2. S

    Makita EA4300F Dolmar 421 Oiling Question/Problem

    not familiar with a tsumura bar for that saw, may not have the oil pickup in the correct place. look at your makita bar in the bar rail where it mounts and you can see into the mount hole below. if tsumura bar is not open to the hole below you will not git oil to your chain. if bar is ok, then...
  3. S

    Makita EA4300F Dolmar 421 Oiling Question/Problem

    if we could order .325 set up on that saw, thats the only way i would stock them. i also git complaints about chain throwing.
  4. S

    Seals Dolmar 143

    flywheel side- 962-900-054 - 17x28x6 clutch side- 962-900-051 - 17x30x7
  5. S

    I got the Stihl Flippy Cap woes

    used them on several saws, used the first set about a year ago so don't know if they hold up long term. they seal good and easy to to remove or replace.
  6. S

    Stihl 036 Pro, reasonable repair or should I replace?

    remove the muffler and check piston/cyl. could also check coil to see if it came loose and locked it up.
  7. S

    Dolmar 421problem

    i have a new teal colored 4300 i would swap for yours. made in GERMANY.
  8. S

    Dolmar 421problem

    good to here you got a new saw. as far as the tune, all iv'e sold has been set where they should be. run 5-6 tanks through it then have him check it. but after the problems you've had you may feel better letting him check it out on start-up.
  9. S

    Dolmar 421problem

    send it to georgia and hope they send you a new saw. or get yours fixed correctly. messing with your carb isn't the answer. your saws symptoms when you first posted was an air leak. not fuel related. just because your dealer put new seals in doesn't mean there in correctly. makita should have...
  10. S

    Missing a gasket or two (I think) in Husky 257

    that pin isn't suppose to be covered up, you need the part i mentioned. your dealer should be able to get it.
  11. S

    Missing a gasket or two (I think) in Husky 257

    i looked on a 257 ipl and don't see it but did on a 261 ipl. should be the same. part # 503-72-31-01. check with your local husky dealer to verify. if your 257 doesn't have the peg on inside of cover then your saw never had it -- i think.
  12. S

    Missing a gasket or two (I think) in Husky 257

    look on the parts pic for the bar cover, it shows it on the inside of bar cover picture.
  13. S

    Missing a gasket or two (I think) in Husky 257

    should be a rubber plug in that hole. the back side of your bar cover has a peg that fits into the plug/bushing.
  14. S

    Homelite replacement gas cap..

    97359-A is the part number for the oil cap-- i have a few n.o.s left, 92701-A is for both caps. chainsawlady, did you buy a bunch of n.o.s. homelite parts from someone in minn. 6-7 years ago?
  15. S

    Homelite replacement gas cap..

    part #DA-92701-A is what you need. if you can't find them i have a few sets n.o.s. left.
  16. S

    Dolmar 421problem

    yup, skeptical.
  17. S

    Dolmar 421problem

    sending the saw back to makita is probably a formality.
  18. S

    Dolmar 421problem

    sounds like it may finally get resolved like it should considering the run around you'v gotten. good to hear that.
  19. S

    Dolmar 421problem

    call your dealer and tell him how your saw is running after getting it back from makita repair center, i think they will give you a new saw if you bi*ch enough. don't run it the way it is.
  20. S

    Dolmar 421problem

    sounds like an air leak!!
Back
Top