Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. S

    Saw pants

    Hope this is in the right spot. anyone have a brand or model on the lighter weight safety saw pants, if you use them? I am thinking if I got some of these fancy light weight pants I would wear them. Like many I don't wear chaps because of the bulk and stiffness. Use would be for personal...
  2. S

    Want to Sell NEW 2022 BUILD HUSQVARNA 3120XP CHAINSAW POWERHEAD $1759 USD SHIPPED

    Do you carry full line ? Also do you have any 395xp? Thank you
  3. S

    Saw chain and bar question

    Thanks guys for the help been awhile since I been here, still great help here.
  4. S

    Saw chain and bar question

    Does that sandwich the bar tip, that's how I build mine I don't want any part of drilling the nose gear
  5. S

    Saw chain and bar question

    Goodnight huskyman what length bar on that last pic? Is that a 3120 on it? Would be nice but it's gonna be tight if I can even get the 395 but 500 more for the 3120 not gonna happen unfortunately.
  6. S

    Saw chain and bar question

    Thinking about looking at a husqvarna 395 need for big trees and also some milling. Anyway thinking maybe getting around a 3ft bar and also maybe little longer for milling. What size/length do bar increase by in inches? Also prob another silly question but how do you figure out what chain length...
  7. S

    heat exchanger

    what chemicals are you guys using to clean your PLATE exchangers? i normally use CLR and let it sit but looks like i forgot now i need to use something a little stronger to take care of this quick to get it back up and running.
  8. S

    Got a apple tree today and milled some of it

    oh yeah you use anchor seal too?
  9. S

    Got a apple tree today and milled some of it

    just apply to sides and end also?
  10. S

    thoughts on my chains

    i sharpen my dads chain for a 16" stihl chainsaw i believe is a .325 chain crosscut only, should i sharpen the same way? except for file size of course! think using 3/16" for that one cant remember dont do those alot
  11. S

    thoughts on my chains

    ok i will get on all this great info, and hopefully get my chains where they need to be, prob dont matter now with new info , but the settings for the 511ax for my chains were 60* down 10 for motor angle, and table angle is at 30* down 10, and tilt on the table is down 10.
  12. S

    thoughts on my chains

    id better check the wixey angle again i might have not done right, saw is husqvarna 460 3/8" pitch .058" these are both 24" chains, mostly my crosscut is 18" though. milling i have mostly red oak right now hand touch up is 7/32" file i forgot to write down what my oregon 511ax grinder settings i...
  13. S

    thoughts on my chains

    cross cut pics
  14. S

    thoughts on my chains

    some pics of my chains for some thoughts, opinions what you see. the cross cut pics they are decent and cut ok but whatever i do it never feels close to the feeling of putting on a brand new chain. i do know the crosscut chain has its rakers a little to low for the strength of my saw got a...
  15. S

    Posting a Craig's List add

    plus about 3% for paypal
  16. S

    Sharpening

    would you buy a oregon 557849 or a granberg similar clamp on sharpener
  17. S

    Stacking instruction help

    still wood right ;) kidding
  18. S

    Stacking instruction help

    thats one heck of an offer and i appreciate that, but i'll have to pass i dont have enough room for a few of those. thats one heck of a setup though, esp for rotating piles.
  19. S

    Sharpening

    i think the greats here should have a shootout and whoever thinks there the best at machine and/or by hand, should make a video for all of us under achievers and be the ultimate Stickie here. i know theres youtube but you never know whats right, or point out this or that
  20. S

    Sharpening

    isnt it kinda hard to keep the teeth the same length doing it like this?
Back
Top