Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. P

    basegasket

    what should i use for the head gasket on my ryobi. i no the local autoparts stores sell gasket material but they have different types such as cork and rubber so what should i use?
  2. P

    tanaka bar mount studs

    its not stripped they go in and hold snug but the threads screw out in the same direction as the nut loosens
  3. P

    tanaka bar mount studs

    its a ecv 4501 when i loosen the nuts the whole stud comes out
  4. P

    tanaka bar mount studs

    how do i keep the whole stud from screwing out of the saw when i take the chain break off
  5. P

    Runaway chain!!!!!

    Ill get right on that!
  6. P

    Runaway chain!!!!!

    I have a 4501serious ecv tanaka and the the chain spins at idel the saw runs fine and idles well but the chain scares me. Also when i put the chain break on it stalls the motor. Any ideas?
  7. P

    What was your lastest Goof Up

    I put the primer bulb in backwords and it took me forever to figure out why i wasnt getting primer fuel and then i striped one of the intake bolts so now im trying to figure out how to fix the striped hole
  8. P

    Brand Pronounciations???

    poll-an doll-mar husk-ah-varn-ie steel re-ob-uh cravs-man mac-uh-lock shin-daw-ah
  9. P

    once in a life time saw project ( I HOPE!!!!!)

    Yes it does turn that way but clockwise is the way the clutch loosens so thats were my problem is that does not make sense to me
  10. P

    once in a life time saw project ( I HOPE!!!!!)

    o ok i understand now, but why does the starter cord pull the saw in an opposite direction rather than pulling it the way it is supposed to cycle
  11. P

    once in a life time saw project ( I HOPE!!!!!)

    but wouldn't it tighten up as it spins if turning the correct way
  12. P

    once in a life time saw project ( I HOPE!!!!!)

    i dont understand how a clutch could unscrew if its turning the right way
  13. P

    once in a life time saw project ( I HOPE!!!!!)

    im just going to have to break down and buy a kit but as far as the clutch cover i no it wasnt the greatest idea but i wasnt expecting thee wide open throtle so yea i am having a wonderful adventure
  14. P

    once in a life time saw project ( I HOPE!!!!!)

    Well let me start off by saying i am no stihl certified mechanic by far, but i do like to tinker. I am new to AS and i have made a few posts and i would like to thank all of you for helping me along the way. The people here are nice and willing to help and that really helps someone in need. I...
  15. P

    carb settings?

    Update I just realized that what i had said was wrong i had the needles in backwords and it didnt damage the seats or anything like that but now that they are in corectly it will not pull fuel when they were in wrong i got fuel well actually way way to much fuel it ran eide open and surged and...
  16. P

    carb settings?

    i have been reading up on my problem and i read that if your low speed needle is set to lean that it will cause the saw to race and surge thats kinda the problem that i am having it will fly away then about ie and then it will take off again and when i hit the gas it will speed up and i let off...
  17. P

    carb settings?

    ok i have got them in the right place and started it now it will run wide open wont idle down even when the butterfly is closed and i can turn the needles in and still wide open
  18. P

    carb settings?

    unfortunatly that is a design flaw they are the same
  19. P

    carb settings?

    and i took it to a shop and had them pull the needles out and didt tell me which was which is the longer one on the left or right?
  20. P

    carb settings?

    im trying to set the carb on my ryobi 10532, and i called and they said L-1 1/2, H-1 1/4. does that sound right i cant seem to get it dialed in, any suggestions its takin a while to pull fuel
Back
Top