Search results

I’ve got a new or nearly new set of Buckingham climbing gear for sale. Pictures show it better than I can describe (mostly due to my very limited knowledge). Feel free to ask questions and to make an offer.

Up for sale is one of my Rattler ported Husqvarna 288xps. This saw has an oem HD/high top setup and an oem full wrap handle. The cylinder is an oem KS non decomp that was ported by Rattler Mike. He also split the cases and put in new bearings and seals at the same time. This one has had one...

Up for sale is my ‘restored’ oem 288...awhile back I was fortunate enough to come across some hard to find nos parts and I decided to build this saw with them. New/nos parts: p/c, brake/clutch cover, tank, recoil, wrap handle, high top cover (filter and elbow too). Cases and oem muffler were...

Offering up my MMWS 562. Saw has seen ~20-25 tanks total between me and the original owner. Starts, idles, oils, runs, and cuts flawlessly. Offered with full wrap, dual dawgs, and your choice of standard gray clutch cover or special order orange one. $725 shipped PayPal f&f to the lower 48 US.

For sale is my mmws 262xp. I purchased this saw from another member a couple years ago, and it has been dead reliable and a great saw for me. Please feel free to ask questions and I’ll do my best to answer in a timely fashion. I’m asking $550 shipped and I’ll include a lightly used 18” sugi lw bar.

Nice 272xp with later mahle decomp cylinder and oem HD filter setup with new (nla) HD filter installed. Previous owner engraved numbers into the tank ‘footpad’ otherwise the saw is clean. Starts, idles, runs, and oils well. Asking $375 shipped. Feel free to ask questions...

Nice clean 268xp for sale. Starts, idles, oils, and runs like it’s supposed to. These aren’t easy to find in decent shape anymore. I’m asking $375 shipped. Feel free to ask questions.

Husqvarna 266xp for sale. Only one I’ve seen with the large recoil decal and plastic flag. Everything works and the saw is in nice shape. Asking $375 shipped. Feel free to ask questions.

371xp ported by Terry Landrum at wicked work saw about 4 years ago. At that time, the cases were split and new oem bearings and seals were installed along with the ported oem p/c. Saw runs flawlessly and strong. Buyer gets choice of oem full wrap and big dawgs(pictured) or a oem half wrap and...

Nice used 359. Saw starts, idles,runs and oils as it should. $275 PayPal f&f shipped.

Looking for an oem cylinder or p/c for a 371/372 husqvarna (50mm) in either good used or new condition. Thanks! Sent from my iPhone using Tapatalk

I've come across two 272xp huskies this week..both of which are now mine. After taking the muffler off to inspect the piston on both saws, neither have a gasket...from Out to in it goes muffler, heat shield, cylinder. Is this correct? On the ipls from husky I don't see a gasket, but they're...

Can somebody identify make/model of this saw?

Looking for an nos or good clean HD, 'west coast' air filter for 268/272xp saws (or for a supplier). OEM part # 503 55 11. Thanks in advance

Looking for a good used 385xp recoil. I'll take just the cover or a complete assembly. Anybody have one they'd part with? Sent from my iPhone using Tapatalk

Looking for a felling spike/dawg for a 242xp. Anyone have one they'd be willing to part with? Sent from my iPhone using Tapatalk

I'm looking to buy a cosmetically decent, preferably oem 272xp. Anyone have one they're willing to part with for a reasonable sum? Sent from my iPhone using Tapatalk

Sent from my iPhone using Tapatalk

I have a 338xpt that starts fine, idles fine (for awhile) and will accelerate fine (once) before stalling and dying. It's repeatable..I thought carb check valve, so I replaced the carb..but it's the same. I'm hoping you guys can save me some time and tell me if it sounds like fuel line, primer...

I've lurked on here quite awhile, bought and sold a little, and would like to think I've learned a lot from this site. I'm not a professional logger, but I do enjoy working on and cutting with my saws. Because of the disease lots of people on here seem to suffer from, I have more saws than i can...