Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. Oly's Stump

    Grinding chains with 511A

    I have 2 grinders. I use the Oregon 511AX for sharpening my chains and I use the Northern Equipment knock off grinder for the rakers. The Oregon is of course better quality. I only use stihl full chisel chain and I just leave my grinder set up as 60/30/0. Some guys use 25 degree for full chisel...
  2. Oly's Stump

    Sandvik cutter wheel dura disk

    The Dura Disk is no longer made but they still offer parts. Have not used the Revolution wheel as of yet.
  3. Oly's Stump

    Homeowner Needs Advice on If Stump Grinding Purchase Is Practical

    Look into a Alpine Magnum. I am assuming you probably just want the stumps below ground level.
  4. Oly's Stump

    Carlton 8018 clutch

    Thanks Moe for the info! I have adjusted it as far as the lever while go with it touching the housing. I have been re-adjusting the past year and now its too its end. I called my dealer on friday afternoon and he said they could get it in on Monday morning and should actually be done by Monday...
  5. Oly's Stump

    Carlton 8018 clutch

    I believe my clutch is toast. Stays engaged and will not disengage. Anyone ever change a clutch? How hard was it? Looks like its probably going to the dealer on Monday.
  6. Oly's Stump

    disabling safety switch on carlton 8018

    Moe...I replyed to your message.
  7. Oly's Stump

    disabling safety switch on carlton 8018

    I just checked mine and its a Omnex remote. They must have changed them in 2006.
  8. Oly's Stump

    Green wheel for angle grinder?

    Contact Alpine magnum stump machines. They have a website and I believe they sell both green wheel and diamond wheel.
  9. Oly's Stump

    disabling safety switch on carlton 8018

    Thats correct. I have the toggle switch right on my wireless remote. What year is your machine Moe? I have a 2006 8018.
  10. Oly's Stump

    One of those days...

    I know what you mean...been there done that! LOL
  11. Oly's Stump

    Stump grinder teeth replacement?

    X2 Fairbanks, Thanks for sharing. I have one question! I have the sandvik wheel on my 8018 TRX and those carbide are much harder then lets say Rayco Super teeth. My green wheel on my bench grinder has difficulty sharpening the carbide. Are you using the green wheel from Alpine or are you...
  12. Oly's Stump

    Carlton 8018 TRAX

    I will give that a try and now that you mention it they are real old. Thanks!
  13. Oly's Stump

    Carlton 8018 TRAX

    OK guys...The other day I tighten the engine belt and messed with the actuator and now I have not had a problem. Grinding all day yesterday (finally getting busy) and machine working good. Thanks Moe on that hand lever kit info. If I have trouble with it again I will get it. Now I got to figure...
  14. Oly's Stump

    Carlton 8018 TRAX

    Yes it will easally stop. Today I cut a number of stumps and it never did it. Go figure! I will check the alignment. Thanks paccity
  15. Oly's Stump

    Carlton 8018 TRAX

    Anybody having problems with your 8018 where the cutter wheel still wants to turn after the clutch is disengaged? Sometimes mine will do that even at idol. Trying to figure out! I adjusted the actuator but nothing seems to help. Has anyone ever adjusted the clutch?
  16. Oly's Stump

    Custom stump grinding truck

    Very Nice Moe.
  17. Oly's Stump

    Sanvick Teeth

    OK...went back to their website (New River) and found the saber teeth. Anybody use the saber teeth? What is the difference? Can the saber teeth be sharpened? I will be putting in an order for some teeth coming up. I have a 2006 Carlton 8018 TRX with the New River wheel and not the Carlton...
  18. Oly's Stump

    Sanvick Teeth

    I heard that New River Equipment has a new tooth for sandvik wheels but I checked their website and could not find them. Heard they were called sabor tooth or something like that. Also heard that they don't even manufacture the Dura Disk II anymore. Have to go with the Revolution wheel.
  19. Oly's Stump

    Rayco cutter wheel bearings

    I dread replacing them bearings for sure. Alot of cussing comes from my shop on those days! lol
  20. Oly's Stump

    Rayco cutter wheel bearings

    Also if the shaft looks like it has worn some, I would just get a new shaft also. Then you will not need to press new bearings on that.
Back
Top