chain

What is on the list what I have by the roll and 25% off the prices in the list + shipping if needed to ship. I do have a bunch of 404 0.63 loops mostly in semi chiesel. If interested send me a drive link count so I can go match up. Mostly oregon but some stihl loops in there. I'm in winnipeg...

As it says 063 quality chain or loops Semi chisel ONLY Full compliment preferred Skips considered 375 3/8 Stihl, Oregon, Woodland Pro/Carlton, ect no Archer please and thank you. Ordering a reel soon if nothing pops up. PM me with prices. Can make my own loops or change them. Not worried...

Part and full spools from 25ft to 100 ft oregon/stihl/sandvik/windsor for sale. Estimated lengths if not indicated new (take or give a little length as im not unspooling all of the part used spools and measuring them with a tape measure) and descriptions are to the best of my knowledge through...

I have 2 saws currently available, a Stihl MS 251 and an 019T topping saw for sale. Both have gone through extensive tune ups, and have new fuel lines, spark plugs, fuel filters, air filters, and BRAND NEW carbs. These are both reliable and great running saws. Extra chains and tools with each...

Just bought a 194t that came with pmm3 semi chisel safety chain. Anybody know if there is a standard picco (low profile) full chisel in 0.43 gauge (1.1mm)?

I have an 066 chainsaw for sale, with TONS of extras. 4 bars, 3 brand new and 1 used. The bars are as follows; 1x36" 1x28" 1x20(new) 1x20"(used) 12 brand new chains--Assorted for ALL OF THE BARS. Files Sqrench New carb, air filter, spark plug, ignition module, fuel filter. Asking 1900.00 for all...

Hoping someone can help me identify this chain by the profile... I can't really tell if it's semi-chisel, ripping, or ?

** LISTEN TO ATTACHED VIDEO** I just installed a West coast Saw Bark box on my Stihl MS 400 m tronic and I am having doubts on if it is harming the saw or not. I followed the proper carb reset on the manufactures website after install and I use Stihl Moto mix. It cracks and pops a lot. Is this...

Hi everyone. Thanks in advance for your time. I recently acquired a 2011 Echo CS-600P chainsaw (I needed new chaps and a helmet and the saw came with them!). My other saws are Stihls (MS271 and MS180). The man who I got the Echo from said it was too much saw for him. I checked all the fluids...

A nice little homelite 245 followed me home today. Runs fine, but the chain was toast. So I get it on the bench and start tearing it down, I find it's got a .325 bar nose, and an 8 pin. This seems insane to me on a 40cc saw. It's a homelite bar and what I think is a homelite number stamped in...

Been trying to work on my MS200T recently, noticed that the chain cover doesn't sit flush to the body of the saw. Can't see anything blatantly blocking it, so I'm not sure what the issue is, whether it's warped or if there's a piece missing somewhere. Any ideas?

Does anyone know where you can buy a 100' roll of .325, .050, full comp, chisel, NON_SAFETY chain? I guess I'd rather stihl but i don't think they make it without the raker bumps. I've had good experience with oregon but I can't seem to find what I'm looking for.

Hello Chainsaw aficionados, I recently got a secondhand 3120XP in basically new condition with no bar and chain included. I've been working on procuring a bar and chain for ripping with an alaskan mill and I ended up with an Oregon 363RNDD009 bar (3/8", 0.063", 115DL) and an Archer ripping...

We are most fortunate to have a new Stihl 201 donated to our Disaster Response Team. Saw will always be on the ground - primarily limbing. All our work is at ground elevation. Came w 14 bar. I would welcome suggestions on best bar and chain for that purpose. Thank you! My goto saws going fw...

I just bought a nice MS361 from a fellow who had a 20" bar on it. I want to put a 24" or 25" bar on it, Rollomatic, the extra light version if possible. I would also like to try a ripping chain and a reasonably aggressive crosscut chain. My current 026 has a chain with a yellow mark on it and I...

Hey guys, I have a opportunity to buy a Bell industries K6 chain grinder in good condition and a silvey chain grinder in good condition. Guy told me to make an offer and I don’t have a clue as to what to offer for these. Something fair for him and I would be great. Any information would be good...

Can you run 3/8 .50 chain on a 3/8 .63 bar? Would the chain be loose because its not thick enough

What are the chances we ever see the Husqvarna X-Cut chain come out in Skip-tooth? I have come to really like the standard X-Cut chain and was kind of bummed when I just went to order some new Skip tooth chain and realized that they don't make an X-Cut skip tooth version.

Heya folks, Got this used ms250 up and running, but still can’t get it in good working condition. Bought it a new bar and chain and using stihl oil to rule out those variables. I’m certain my chain isn’t too tight as I can pull it up enough to reveal the drive link. The chain, however, feels...

Hi guys, I was going to make some comments on existing threads, but i thought I'd start my own here. Before I do though, I want to shout out to @Gaudaost and @trains for their help either through posting their own learnings or through directly helping me to understand things more. A few...