problem

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. F

    Stihl 026 common problem (hard to start)

    Hi, just got a 026 from a friend a he told me that he can not start (hard to start) it he needs to pull it 12 to star. our local Stihl dealer look at it and told us that is a model defect. do you know something that I can do for that This was only use for 10 contracts and stored is like new...
  2. E

    At wits end with ms250

    So I'm a newbie. I've done a little bit of clearing for work, so I'm comfortable with saws. Planning on getting some vacant land soon and figured I'd need a saw to clear stuff on there/fire wood. I have this condition where instead of buying a new, working machine, I'll buy an cheap broken...
  3. RGWoodConcerns

    Sick Oak Tree **Help**

    Located in the Hudson Valley- NY-We have a very large 75+ year oak tree in our front yard. It is dying at the top showing browned or no leaves in certain portions. In addition, a section of the lower bark is coming loose with carpenter ants, smaller ants and eggs living in the dead wet bark. I...
  4. C

    Vermeer SC292 bogs down when head engaged BUT...

    only about 50% of the time. The rpms will drop and the motor sounds like it's trying to sort a bad idle. This can also be caused if I take an ambitious bite or sweep on an angle in to the stump. High idle doesn't recover until I've either disengaged the head and rolled the dice again on...
  5. A

    Stihl 048 AV muffler problem

    Hello, everyone. I've been reading the forum for a long time, but it's the first time I'm writing. A few days ago I bought my much-desired Stihl 048AV. I bought it from England at a good price, the seller said that the chainsaw didn't work. I disassembled and cleaned everything, the problem was...
  6. wireedm

    394xp Big Bore Issue

    My 394xp was getting impossible to restart once warm so I knew the compression was getting low. Had it checked and sure enough, it was down to 100psi. In looking at the options I decided on the big bore kit from Little Red Barn...
  7. Pakai Boti

    Al-ko chainsaw

    Hello, i have an Al-ko kb35\35 chainsaw, but i can't figure it out where the throttle cable goes, somebody tied it with a wire, the carb is wt439A
  8. Jeff Markley (zone 7b)

    Growth on Bark of Pear Tree

    I planted a pear tree in my backyard about 6-7 years ago. For the past two years it has been providing fruit, but the fruit stays very small (about the size of a golf ball) and very hard. There is a strange growth covering pretty much all of the bark. I've done a ton of research and it doesn't...
  9. L

    Morbark chipper ?

    Looking for any information on a 20/70 morbark chipper gas 35hp Especially weight since towing on a smaller truck Any issues Thank you for any information
  10. Pastornater

    Jonsered 2159c idling tuning issues

    Hi all, I have read many tuning posts and have applied a lot of what I have read. The chainsaw was running rough for a day, I put it away for a week and then I couldn't get it to start to save my life. I replaced the diaphragm and other basic carb kit parts. Pulled the head to make sure the...
  11. T

    Advice on the irregular situations

    Hi everyone this is my first post. I have a disgruntled homeowner from the neighboring property of where I just took down a large maple cornered in by powerlines. So i get the tree down and cut the stump, and my subcontracted stump grinder guy comes in and grinds the stump in the morning. I...
  12. Andrew W.

    Okay so this worker

    Okay so I watched a guy flush cut a stump today, now the way I was shown was, you clear out as low as you can go without hitting dirt, rocks, chain link fence, and other stuff, get on your knees put the saw sideways, eyeball the bar levelness and cut 90%, insert wedge or bark and Finnish the...
Back
Top