BIG JAKE
Let’s go Brandon!
I have a Sandvik bar that I need help ID'ing. Says made in Sweden 511, 1786-50 1.27mm/.050" 3/8"/62 DL. What saws will this bar fit?
Thanks in advance,
Jake
Thanks in advance,
Jake
Need help to ID this Sandvik chainsaw bar
- Thread starter BIG JAKE
- Start date
Help Support Arborist Forum:
Old Sandvik catalog lists the 1786-50 as a 16" bar, 3/8 pitch, .050 gauge using a 62 dr. link chain.
For Stihl -051av, 051ave, 075ave, E30, 08S, S10, 07S
For Stihl -051av, 051ave, 075ave, E30, 08S, S10, 07S
BIG JAKE
Let’s go Brandon!
Bummer-was hoping I could use it on something I had. Thanks Ray
evang
New Member
Another Sandvik bar
Hi Ray:
Could you tell me what a Sandvik 3270-45 (1.47mm/.058" .325'/64DL) fits?
Thanks in advance,
Evan
Hi Ray:
Could you tell me what a Sandvik 3270-45 (1.47mm/.058" .325'/64DL) fits?
Thanks in advance,
Evan
Sandvik 3270-45 fits Jonsereds 50, 50s, 51, 51s, 52, 521, 45, 49sp
It's listed as a 15" bar, .325 pitch , .058 gauge using a 64 dr. link chain.
It's listed as a 15" bar, .325 pitch , .058 gauge using a 64 dr. link chain.
evang
New Member
Sandvik bar
Great - thank you, Ray!
Evan
Great - thank you, Ray!
Evan
mikerecike
ArboristSite Member
Sandvik Bar equivalent / help for Danarm Frontier 5r
Hi Ray
I have the above saw and am really struggling to replace this knackered bar. Ideally I'd like a smaller one - 14". Can you help tell me if that's possible? How can I cross ref it to an oregon or other manufacturers bar for example. Or if this fits into a generic type?
I have tried everywhere!
thank you
Hi Ray
I have the above saw and am really struggling to replace this knackered bar. Ideally I'd like a smaller one - 14". Can you help tell me if that's possible? How can I cross ref it to an oregon or other manufacturers bar for example. Or if this fits into a generic type?
I have tried everywhere!
thank you
PULLINmyPOULAN
ArboristSite Operative
Need an Id on this Sandvik numbers are 605 1669-48 .050 3/8 60 dl
Old Sandvik catalog lists Husqvarna L77, 160s, 280cd, 1100cd so that is an Oregon D009 mount. Very common mount. It is a 16" bar .050 gauge, 3/8 pitch and uses a 60 drive link chain.
http://www.acresinternet.com/cscc.nsf/BMP/17?OpenDocument
PULLINmyPOULAN
ArboristSite Operative
Thanks Ray
Jon1212
Riff Raff Fart Knocker from other Forum's.
Ray,
That's some very impressive guide bar knowledge.
Check out the bars on top.
That's some very impressive guide bar knowledge.
Check out the bars on top.
SawTroll
Information Collector
If so, it should fit any saw that use the K095 (small Husky) mount!
Jon1212
Riff Raff Fart Knocker from other Forum's.
I like Sandvik bars.
SawTroll
Information Collector
Jon1212
Riff Raff Fart Knocker from other Forum's.
A176 sounds strange, while D176 would fit many Echo saws and more?
That's what I thought as well. Eccentric, and ModifiedMark helped me identity them.
There are subtle differences between the A176, and D176.
SawTroll
Information Collector
It should be about tail size - usually the D bars are wider than the A bars, and the oiler holes won't add up.
Jon1212
Riff Raff Fart Knocker from other Forum's.
Nope. The adjuster holes are too far from the stud slot.
SawTroll
Information Collector
It should be easy to determine if they have A, K or D tails by comparing the tail profiles/sizes to some known mounts....
Jon1212
Riff Raff Fart Knocker from other Forum's.
It should be easy to determine if they have A, K or D tails by comparing the tail profiles/sizes to some known mounts....
Uncle Niko,
I'll get some pictures of the "A" versus a known D176, and post them up here.
