BigDaddyR
Addicted to ArboristSite
Thanks Jerry. You're a good man. I don't care what Ron says about you. LOL.
Rick
Sure is quiet in here....do I need to start a fight?
- Thread starter caleath
- Start date
Help Support Arborist Forum:
Thanks Jerry. You're a good man. I don't care what Ron says about you. LOL.
Rick
BigDaddyR
Addicted to ArboristSite
Thanks Jerry. You're a good man. I don't care what Ron says about you. LOL.
Rick
LOL.....I waited til the Christmas rush got cleared up. My postal lady told me they just cleared their station of pent up mail yesterday.
Too bad Ron went to bed, I could reroute some calls to him from those asking me why their furnaces are not working tonight, he`s got his feet wet now as a furnace tech.....
Never had any AM Husky coils before ? I don't have any extras either. I would just check all the connections first. Check the little brass piece behind the coil too,seen them break before.
BigDaddyR
Addicted to ArboristSite
A friend is a post master for a local town and he was sending help over to Westminster to help them clear theirs.
Rick
BigDaddyR
Addicted to ArboristSite
Brass grounding strap checked. Got familiar with that when I had it all torn down. Connections all tight. Stop switch engaged shorts the circuit.
Spark tested it and spark is very intermittent. First pull tries to start with choke in and nothing after.
I can get a new coil but just want to make sure its not something I can repair like the boot or wire.
Rick
BigDaddyR
Addicted to ArboristSite
Brass grounding strap checked. Got familiar with that when I had it all torn down. Connections all tight. Stop switch engaged shorts the circuit.
Spark tested it and spark is very intermittent. First pull tries to start with choke in and nothing after.
I can get a new coil but just want to make sure its not something I can repair like the boot or wire.
Rick
Got a little dusting of white here so far and staying around -17C ,no wind yet. They are trying their best to get me out there tonight to work on broken down furnaces but I have elected to be armchair tech so far.....LOL
little possum
Crash and Burn
Sticking to just one, although the whole team from what Ive met seems to think I am a good guy? Plus, I know they can beat my butt in a pillow fight, aint trying to make them mad. hah. Definitely been quite a change from a homebody that didnt need nobody but his family and dogs..
But she loves shooting guns, so I am set! haha
But she loves shooting guns, so I am set! haha
Thinking bad coil ? You can try the coil off yer 365 on it. Purdy sure its the same.
Thinking bad coil ? You can try the coil off yer 365 on it. Purdy sure its the same.
Yer in deep doodo ! LOL
The test/check for your switch is actually that it don`t short the coil in the off position....just sayin.
BigDaddyR
Addicted to ArboristSite
? When the stop switch is engaged meaning pushed down to stop the saw, blue wire, black wire, all have continuity with the cylinder etc. When stop switch is off meaning in he saw run position resistance reading is 210. I think it's supposed to be impedance but I honestly don't remember how to check the impedance of a coil to see what it's supposed to be or where I would get the value for that. I will look coil troubleshooting up in the Husky Service manual.
Like John said I will see if my 365 coil is a fit. gives me a known good one to test with.
BigDaddyR
Addicted to ArboristSite
Good point. I'll cross reference the numbers on the coils to see if it's a fit. I almost feel like it's a broken wire in the spark plug cable but I don't know if this one can be replaced.
Slug time !
BigDaddyR
Addicted to ArboristSite
Night John! Hope Arthur doesn't keep you up.
Time:
