Pop Off Pressure- Do you know where yours is at ?

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Pop Off Pressure - Do you know where yours is at ?

  • Yes

    Votes: 4 33.3%
  • No

    Votes: 6 50.0%
  • Does it matter ?

    Votes: 0 0.0%
  • I just don give a damn.

    Votes: 2 16.7%

  • Total voters
    12

OilHead

ArboristSite Guru
Joined
Mar 21, 2007
Messages
638
Reaction score
40
Location
Bay Area, Ca.
Seeing as there is no information on the subject figured I'd post this question as it will eliminate nags on modified saws. The article can be found at - www.aerocorsair.com - Inventions Page - Pop Off Pressure By: Alex Varv Jan 2008. I wont be taking any question untill after the lecture. Your car or truck does not have a motor in it . It has an engine. Motors are electric.
 
If any one knows how to transfer the page over here then we'll have it for future referance should that site go down.
 
Why is this in the Arborist 101 section? By the way, both my car and truck have motors in them. The starter and windshield motors come to mind.:censored:
 
Why is this in the Arborist 101 section? By the way, both my car and truck have motors in them. The starter and windshield motors come to mind.:censored:

LOL.

what is the purpose of this anyway? motor, engine, internal combustion power plant, etc... where are we going with this?


LXT...........
 
Google Walbro+popoff and you will get about a zillion hits from the remote control airplane and go-kart crowds. I still don't understand popoff though. I just set the needle lever to the right height and leave the spring tension how I found it. Usually stuff runs good that way.
 
If you want to know my popoff pressure you should ask my wife
not me.
- :chainsaw: - OK 102 views & no yes votes. A member from another camp & myself have gone into the test mode to see if we can eliminate nags from saws after saws have been modifyed including just gutting the muffler & opening up the total exhaust area to as much as 150 % the size of the port it self. I have all my # but am waiting for our friend to show up here. You should have a clue by now what were lookin at. :givebeer:
 
modifyed including just gutting the muffler & opening up the total exhaust area to as much as 150 % the size of the port it self


If you need to go to 150%, that tells me that the muffler volume is to small.
 
modifyed including just gutting the muffler & opening up the total exhaust area to as much as 150 % the size of the port it self


If you need to go to 150%, that tells me that the muffler volume is to small.
- Were talkin about where the exhaust exits the muffler . Not a dime size hole that is less than 1/2 the total area of the exhaust port on the cylinder. I did hear back from the other camp today & so far results have been excellent . He is still workin on a tilly that is really out to lunch. It's being measured at 50 psi , a wonder the saw even ran with it or has'nt had a major seizure . Ultimately were trying to come up with a # we can call the defacto standard. :chainsaw:
 
Were talkin about where the exhaust exits the muffler

I am aware of that. I have worked on 2 stroke motors that are between 5.5 and 6
hp per ci and none of them were anywhere near 100% much less go to 150%.
 
Google Walbro+popoff and you will get about a zillion hits from the remote control airplane and go-kart crowds. I still don't understand popoff though. I just set the needle lever to the right height and leave the spring tension how I found it. Usually stuff runs good that way.
- If you perform an extensive muffler mod you will most likely experiance run on when returning back to idle. It is a dangerious situation that needs to be addressed with more than just richening up the L. Update we now have one other person that is fixin to lower the pop off pressure on a 441 . It has real bad nags I have seen the video. Running 10% alky he has allready opened up all the orfaces but still doesnt have enough fuel yet. Should have some results back on that one pretty soon.
 
Are you talking 100% of the flange area, or 100% of the actual port area?

100% of the port area is no problem, even 150% is likely ok. But 100% of the flange area is likely approaching the maximum for a work saw.
 
- If you perform an extensive muffler mod you will most likely experiance run on when returning back to idle. It is a dangerious situation that needs to be addressed with more than just richening up the L. Update we now have one other person that is fixin to lower the pop off pressure on a 441 . It has real bad nags I have seen the video. Running 10% alky he has allready opened up all the orfaces but still doesnt have enough fuel yet. Should have some results back on that one pretty soon.

Could this be why I can't dial in my little Craftsman with the muffler mod? And is there a way to modify pop-off by just stretching or compressing the needle lever spring, just guessing at how much tension you need? I would try that with my disposable saw just to experiment.
 
Yes, to lower pop off, just shorten the spring a coil or two at a time, want to increase pop off streach the spring.
 
Could this be why I can't dial in my little Craftsman with the muffler mod? And is there a way to modify pop-off by just stretching or compressing the needle lever spring, just guessing at how much tension you need? I would try that with my disposable saw just to experiment.
- :chainsaw: :chainsaw: Was waiting for the other guys before I posted my findings but here goes. 15-17 Psi seems to be the majic # so far. When cuttin off the spring take a turn off from the other side as you go. As time goes on think were gonna find a lot of saws that are at 20 or more which was the case on the walbro from a 310. Just get it off that high area but no lower than 15. It will be fat after the mod so be ready to adjust it right away or you will foul out the plug that or turn both the L & H back in 1/4 turn lean & set max rpm from there.
 
Where is the dipstick on a motor to check the motor oil level??! Now I'm really confused. Sorry to derail the train even further...
 
Where is the dipstick on a motor to check the motor oil level??! Now I'm really confused. Sorry to derail the train even further...
- The reason you cant find the dipstick is because electric motors dont have them only engines.
 
Could this be why I can't dial in my little Craftsman with the muffler mod? And is there a way to modify pop-off by just stretching or compressing the needle lever spring, just guessing at how much tension you need? I would try that with my disposable saw just to experiment.
:chainsaw: If you have to cut more than 2 turns off each end it's probably better to stop by your dealer and have a look at his spring box & find one thats closer in length to where you need to be & still maintain 1 or 2 turns on either end for superior accuracy . Mine charged me $ .56 , so is basicly a 100 % free mod or 20 minutes in the shop if you have the carb off.
 
Back
Top