The made in north america Old Magnesium Swap Meet.

[Duke Thieroff]

Hey fellas


Looking for the following for a Poulan 4200
-Nice bar and chain, somewhere from 20-24 inches, Hopefully Poulan branded
-Choke lever
-Bucking spike

Looking also for a Homelite 410 or 540

I got loads of Poulan 3400 parts to trade (just came across a bunch of em in the past few weeks) and some other stuff too.

Chris

 

[leeha]

Looking for a complete Pioneer 1750 or 1850 geardrive chainsaw.
I know someone must have one.





Lee

 

[Big Dan]

I'd trade you a couple of Mini Macs for that motorcycle. :hmm3grin2orange:

 

[promac850]

I'd trade you a couple of Mini Macs for that motorcycle. :hmm3grin2orange:

I raise ya a vintage cast aluminum deck Moto-Mower!

 

[apse]

Now you got my attention.

Wards/Remington SL-4 or PL-4??? The fuel & oil caps says SL-4.

What's the story on it? Needing a carb. box lid?

Send us an email...PM box filling up pretty fast! It feels like good compression. We have another one or two of these laying around.

Thanks,
Brian and Tina

 

[apse]

I'd trade you a couple of Mini Macs for that motorcycle. :hmm3grin2orange:

Gee Dan....

That might be pretty hard to pass up!!!

Harley is not in the trade pile, just in the picture...

Give us a call if you're around,

Thanks,
Brian and Tina

 

[ChainsawmanXX]

Homie EZ going out to a fella in AL

 

[Eccentric]

In addition to the parts I mentioned before, I need a bucking spike for a Poulan 306/245. Also could use a good orange non-PowerSharp clutch cover for a Dayton branded Poulan 306/245. I have a good green 245A cover to trade, plus the other stuff I mentioned in my earlier post. I'll probably just paint my green cover orange to match the saw...

 

[Busmech]

Ron, I can use the front handle. Busmech was looking for a starter assembly for a 707, yours looks the same as my 707.

I think that is the type I need but my 707G needs one that turns the other way, I don't think those are reverseable.

 

[CM76]

I am always looking for Homelite 9-26, 900G - 995G geardrive saws and parts.

I am also chasing early Titan two man saws including Model E, ER, and Bluestreak units. I am also after parts for these machines. Even leads are appreciated on the above!!!!:msp_wink:

I have a decent amount of McCulloch 125 parts I am willing to trade with.

Chris.

 

[Jacob J.]

I am always looking for Homelite 9-26, 900G - 995G geardrive saws and parts.

I am also chasing early Titan two man saws including Model E, ER, and Bluestreak units. I am also after parts for these machines. Even leads are appreciated on the above!!!!:msp_wink:

I have a decent amount of McCulloch 125 parts I am willing to trade with.

Chris.

Hey Chris-

I have a 9-26, a 909G, and a 990G that I can put up for trade but I'm not interested in any Mac 125 stuff.

I'm not really a gear drive guy. I have a pristine 3100G that I'd trade for the right saw or saws too.

 

[CM76]

Hey Chris-

I have a 9-26, a 909G, and a 990G that I can put up for trade but I'm not interested in any Mac 125 stuff.

I'm not really a gear drive guy. I have a pristine 3100G that I'd trade for the right saw or saws too.

Thanks JJ - you definitely have my interest. PM sent.

Chris.

 

[Eccentric]

Hey Chris-

I have a 9-26, a 909G, and a 990G that I can put up for trade but I'm not interested in any Mac 125 stuff.

I'm not really a gear drive guy. I have a pristine 3100G that I'd trade for the right saw or saws too.

You have my interest too Jacob, but I doubt I have anything you'd be interested in.

 

[Jacob J.]

You have my interest too Jacob, but I doubt I have anything you'd be interested in.

You never know what'll turn up...

 

[Duke Thieroff]

Hey fellas


Looking for the following for a Poulan 4200
-Nice bar and chain, somewhere from 20-24 inches, Hopefully Poulan branded
-Choke lever
-Bucking spike

Looking also for a Homelite 410 or 540

I got loads of Poulan 3400 parts to trade (just came across a bunch of em in the past few weeks) and some other stuff too.

Chris

Bueller?

 

[AU_K2500]

Oil and Gas cap, and a B&C for a Homelite E-Z auto

 

[leeha]

Hey Chris-

I have a 9-26, a 909G, and a 990G that I can put up for trade but I'm not interested in any Mac 125 stuff.

I'm not really a gear drive guy. I have a pristine 3100G that I'd trade for the right saw or saws too.

Looks like i'm out of the 3100 game.




Lee

 

[Luis Cabrita]

Side clutch cover - Pioneer 600 series

Anybody can spare me a side clutch cover for my Pioneer 650. I believe anyone from a 600 series is suitable... Thanks a lot...:msp_thumbup:

 

[zogger]

Looking for 24" D176 bar mount

Looking for a 24-27 inch bar for my 245A. Loops an added bonus. Have various old junque..err. I mean quality stuff for swap.

 

[Eccentric]

Looks like i'm out of the 3100 game.




Lee

How will you survive with only the three 3100G's that you have now???:hmm3grin2orange:

My guess/fear is that I'll miss out on Jacob's 3100G and it will soon be on the slow boat to OZ...........................to go on the shelf next to the last 3100G that I missed out on.:frown:



The 1130/3100 spike tracing came in yesterday. Thanks a bunch Lee!:msp_thumbup: