The "unofficial" 6 cube sticky

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Nice saw Nate.

Those Pioneer gas caps have a habit of swelling and getting stuck. They are getting hard to find. Don't leave them screwed down when you have it in storage or leave it with gas in for too long. Something in the gas makes them swell. Maybe the ethanol.
 
Nice saw Nate.

Those Pioneer gas caps have a habit of swelling and getting stuck. They are getting hard to find. Don't leave them screwed down when you have it in storage or leave it with gas in for too long. Something in the gas makes them swell. Maybe the ethanol.

Thanks Tim, yeah I have to put them on and take them off with pliers! They were that way when I got it.
 
I recently had a Pioneer Farmsaw with a very hard to tighten/loosen gas cap myself.

I used the trick of submerging it in non-ethanol straight gas for a week.

I barely touched up one thread on the cap that was too tight with a triangular file, now it screws on and off smooth as new.
 
I recently had a Pioneer Farmsaw with a very hard to tighten/loosen gas cap myself.

I used the trick of submerging it in non-ethanol straight gas for a week.

I barely touched up one thread on the cap that was too tight with a triangular file, now it screws on and off smooth as new.
Nice trick. I'll have to keep that one in mind.
 
7e1333d9cc1611e3b01948fbff65bdf8.jpg
y

Wait! Six? Oh well.

Apart for repairs.
b99deec3f47899bad8ac5632e1e77e99.jpg
 
Nice saw Nate.

Those Pioneer gas caps have a habit of swelling and getting stuck. They are getting hard to find. Don't leave them screwed down when you have it in storage or leave it with gas in for too long. Something in the gas makes them swell. Maybe the ethanol.

I recently had a Pioneer Farmsaw with a very hard to tighten/loosen gas cap myself.

I used the trick of submerging it in non-ethanol straight gas for a week.

I barely touched up one thread on the cap that was too tight with a triangular file, now it screws on and off smooth as new.

that has worked for me. thinkin it's the eth, too.
 
I'm posting this in a few place s to try and get results...

I'm curious to what people in here have for the model 73 serial number for those who own one. According to bulletins I know they made over 55000 model 73 saws but I have yet to see one with a serial number over 10,000. Does anyone in here own a Model 73 that's over serial number 10000? I've seen a 73A in the 11,000 range but that's a different saw all together that I'm not looking into.

Also starting around 10347 they started putting the snorkel air filter system on the saws and you don't see hardly any of those either. I have one serial number 49 50 that has the snorkel air filter system on it obviously it's an add-on but I've only seen a few others. Im researching certain features of this saw and trying to see what all is out there. You can tell from certain parts and pieces the age of it. I have one with no tag and a blank pad but the 6 hole clutch drum on it tells me its prior to serial number 4227. After this serial number they went to a stronger two hole drum.

So these changes tell a lot about the saw. If anyone can share their serial number id appreciate it.It would also be interesting to see what the lowest serial number around is. There is a lot of documentation by McCulloch on the model 73 saw. I'm also checking into the Model 77 but so far there isn't much around on that model. Anyway I'd appreciate anything anyone can share.

Thanks,
Nick

My 73 serial #4950 with 4' bar and snorkel air filter system


c6e814576acaa92bbea7301d280c7dbb.jpg


Sent from my SM-T330NU using Tapatalk
 

Latest posts

Back
Top