What are your firewood saws?

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Depends on what I am cutting. However for falling I primarily use my 026/260's, the 046/460 mutt saw, j-red 670, or the Husky 359, 288 or 2100. For the 2 big Huskies I have everything from a 20", 24", 28", and 36" bars. Also converted my MS260 Pro to 3/8" with a 16" bar that I usually bring with when using the 460 so I can swap bars if need be. Once the tree is on the ground or if I'm cutting up logs at a charity cut or tops, etc. then anything that runs (or stays running) I use. Normally the antique saws that run get brought out in a rotation (sort of) and have tank of fuel run through them cutting up stuff on the ground. Usually when dropping a tree I cut it down with the "big" saw if needed, cut up all the big stuff or cut until it runs out of gas then switch to the "small" saw to cut up the little stuff.
 
Cough...send the 2186 off to be massaged lovingly....

And be done with it.
See that's the conundrum.

The 272 is basically my 2 step plan into a newer 70 cc saw.

I'm torn between keeping the 2186 stock, porting it, or throwing a 90 cc jug on it and then porting it. Or selling it and buying a 395. I really don't know what I'm going to do.
 
See that's the conundrum.

The 272 is basically my 2 step plan into a newer 70 cc saw.

I'm torn between keeping the 2186 stock, porting it, or throwing a 90 cc jug on it and then porting it. Or selling it and buying a 395. I really don't know what I'm going to do.

the 2188 is only 3cc larger then the 2186. would be silly to swap top ends for that. i've ran both that were crazy strong. if you want a shelf queen and 395 is a sweet option.
 
See that's the conundrum.

The 272 is basically my 2 step plan into a newer 70 cc saw.

I'm torn between keeping the 2186 stock, porting it, or throwing a 90 cc jug on it and then porting it. Or selling it and buying a 395. I really don't know what I'm going to do.

Dude.......

Is the 86 not the size of a 372?

Just get it worked and throw a 28" on it. Have a good balance for all worlds. I wouldn't ditch that for a 394. :D Unless you came across on a good deal modded one from a reputable person on here. Its still gonna be heavier than the 86.

It's rare I use all of the 32" bar. Rare.

But not so rare I use the majority of the 28" on the Dolmar.

Stick with the 86 and a 28" bar. It will suit you well, from Zogger wood (when he's not getting the Diablo serviced) to big wood.
 
Dude.......

Is the 86 not the size of a 372?

Just get it worked and throw a 28" on it. Have a good balance for all worlds. I wouldn't ditch that for a 394. :D Unless you came across on a good deal modded one from a reputable person on here. Its still gonna be heavier than the 86.

It's rare I use all of the 32" bar. Rare.

But not so rare I use the majority of the 28" on the Dolmar.

Stick with the 86 and a 28" bar. It will suit you well, from Zogger wood (when he's not getting the Diablo serviced) to big wood.
Yeah I think the 2186 family weighs about a pound more than a 372.

I'm trying to build a stable of saws that hits all of the cc classes though. If I could find a nice G model 372 then I'd fill another class and have a G in the stable too. Again I don't know. At this point I have five saws in the garage that I haven't even used yet. Getting ahead of myself. Although the 350 and the 272 may end up being Christmas presents too. We shall see.
 
And again I'm really impressed by the 461 and 7900.

The nice thing with saws if you can find a clean used model you can even up if you decide to move it at a later date.

461 is what I'm aiming for right now. If I could have one saw that'd be it. I had a line on an 046 but it hasn't pulled through yet
 
And again I'm really impressed by the 461 and 7900.

The nice thing with saws if you can find a clean used model you can even up if you decide to move it at a later date.

You have an 86 and want a 7900????....pfffft.

Get your 86 worked and be happy.

Just .02 coming from someone that has had 2 unlimited coil 7900's for a long time....
 
Well I really like the ported 562 I got from Reed (BGE541)View attachment 534004so I decided to send the 51 to him to get ported, it runs very well now too:)View attachment 534005 they make a great pair for firewoodin.

Oh boy!!!!

I really like the plan Nate!!!!

I would love to run a modded 562 with a 24" bar for a while. For me I feel that would be a darn near perfect firewood saw.
 
Just got my 1st saw. I always used my grandfather's or my buddy went with me to cut wood and used his he cut and I split but now that we moved cross country it was time for me to get one. Echo cs-590 with a 20" bar
d7b90bafeb24253b5207aa485fb8832c.jpg

ee0cf73ad4ac5475af373d86eb8aceff.jpg

161a5ee473fef1b281b7273d35642ac3.jpg


sent from my electronic leash
 
Just got my 1st saw. I always used my grandfather's or my buddy went with me to cut wood and used his he cut and I split but now that we moved cross country it was time for me to get one. Echo cs-590 with a 20" bar
d7b90bafeb24253b5207aa485fb8832c.jpg

ee0cf73ad4ac5475af373d86eb8aceff.jpg

161a5ee473fef1b281b7273d35642ac3.jpg


sent from my electronic leash


Very nice. For the money, that's a tough saw to beat.
 
Back
Top