MS200t bogging/stalling on startup

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I was wondering about that after looking at it again. Still think the carb is the primary suspect? Or should I be looking for seal leaks?
 
I was wondering about that after looking at it again. Still think the carb is the primary suspect? Or should I be looking for seal leaks?
Well if you pressure test first then you can proceed to buy a new OEM carb if need be. You have to either pressure test or try a carb what ever is easier for you.
 
Are the huayi brand carbs the aftermarket ones that you found good? I found another thread where you talked about it, and you spelled it different, but I cannot find a thing about that brand online. Keeps referring me to Huayi carbs.
 
Are the huayi brand carbs the aftermarket ones that you found good? I found another thread where you talked about it, and you spelled it different, but I cannot find a thing about that brand online. Keeps referring me to Huayi carbs.
They are the best of the aftermarket carbs but you will have trouble finding one. Best to buy OEM now. You could send me that carb and I can tell you if its good.
 
I might just take you up on sending you the carb to test.

Currently, I'm digging around in my scrap piles for a block of aluminum to make a pressure tester. I might just make one out of UHMW poly. I don't do much with aluminum.
 
Having a bit of problem fuel related with my rebuilt T200 as well, third carb,- this time it runs great all around except after a 30 second cut, stalls out when it returns to idle and leave it for 30 seconds or so and starts and performs beautiful and does it again after a cut, crankcase vac- press test was 100 percent when I tested it, wonder if the tank breather is a little wonky ???
 
Having a bit of problem fuel related with my rebuilt T200 as well, third carb,- this time it runs great all around except after a 30 second cut, stalls out when it returns to idle and leave it for 30 seconds or so and starts and performs beautiful and does it again after a cut, crankcase vac- press test was 100 percent when I tested it, wonder if the tank breather is a little wonky ???
OEM carb?
 
So, I swapped the carb out with a new one, and tuned the saw. I set the H and the L each 1/4 turn richer than max rpm at each setting. That fixed the no rev problem. That'll do the saw for the odd start in the winter to keep fresh gas in it. Any advice how to tune it better in the spring?
 
So, I swapped the carb out with a new one, and tuned the saw. I set the H and the L each 1/4 turn richer than max rpm at each setting. That fixed the no rev problem. That'll do the saw for the odd start in the winter to keep fresh gas in it. Any advice how to tune it better in the spring?
I tune at 1 turn out each the H and L. minor adjustments after that.
 
I think I wound up with about a turn and a quarter out on each screw. I started with each one one turn open from closed, then got it started and warmed up. Turned the idle control screw till it was just starting to move the chain, set the brake, found the fastest idle on the L screw, then added another 1/4 turn richer. That had the saw snapping up pretty quick. Then I released the chain brake, and ran it full blast and adjusted the H screw till I found what sounded like the fastest rpm, then richened it up 1/4 turn. It burbled a little at that with no load. I think all in all , each screw was opened about a turn and a quarter. Then I backed out the idle screw till the chain was no longer trying to move.

I wasn't too concerned about tuning it just right as it was -20C outside, and I had no intention of cutting anything. More just making sure the carb worked.
 
I think I wound up with about a turn and a quarter out on each screw. I started with each one one turn open from closed, then got it started and warmed up. Turned the idle control screw till it was just starting to move the chain, set the brake, found the fastest idle on the L screw, then added another 1/4 turn richer. That had the saw snapping up pretty quick. Then I released the chain brake, and ran it full blast and adjusted the H screw till I found what sounded like the fastest rpm, then richened it up 1/4 turn. It burbled a little at that with no load. I think all in all , each screw was opened about a turn and a quarter. Then I backed out the idle screw till the chain was no longer trying to move.

I wasn't too concerned about tuning it just right as it was -20C outside, and I had no intention of cutting anything. More just making sure the carb worked.

Did you have the "window" open between the engine & the carb compartment to allow for some warming of the carb?
 
I think I wound up with about a turn and a quarter out on each screw. I started with each one one turn open from closed, then got it started and warmed up. Turned the idle control screw till it was just starting to move the chain, set the brake, found the fastest idle on the L screw, then added another 1/4 turn richer. That had the saw snapping up pretty quick. Then I released the chain brake, and ran it full blast and adjusted the H screw till I found what sounded like the fastest rpm, then richened it up 1/4 turn. It burbled a little at that with no load. I think all in all , each screw was opened about a turn and a quarter. Then I backed out the idle screw till the chain was no longer trying to move.

I wasn't too concerned about tuning it just right as it was -20C outside, and I had no intention of cutting anything. More just making sure the carb worked.
I never in my life tuned one at that temp but here at Sea level and around 40 or so degrees Fahrenheit 1 turn out works fine.
 
Back
Top