What Saw's On The Kitchen Island Today

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
That's a good one lol. The special is in the basement chilling lol.
Thanks.
Patients, being ready to pounce when the deal comes up, sometimes that means being willing to drive a couple hrs to make it happen.
Drove a couple either way last night to pick up another stihl :).
I've been waiting for yrs to get one, anyone want to buy my Tecomec super jolly, it's the one with the hydraulic clamp.
View attachment 801238
whad that cost ya ? nice unit
 
A lot less than a new one and a good bit less than a used one :cool:.
Thanks. Planned on trying it out last night but it didn't happen, maybe later tonight.
I bought mine new for half price 550,00 up here with 10 cbn wheels 38ths and 325 with the foot pedal
and hedge trimmer sharpener attatchement.It was new from a retired dealer.what did you get yours for?
 
I must have missed the 300 one.
Those 461 are great saws, little muffler mod and a timing advance and they come to life, ported even more.
Like I always say, what works for one doesn't always work for everyone, I like to run them all, the handling on the huskys is the best for me, stihls are getting a bit more angle on the top bar these days though so they feel a bit better :).
What are you doing in the picture, hard to see on my phone.

Even my underwear is ported.


Sent from my iPhone using Tapatalk Pro
 
I bought mine new for half price 550,00 up here with 10 cbn wheels 38ths and 325 with the foot pedal
and hedge trimmer sharpener attatchement.It was new from a retired dealer.what did you get yours for?
Not that cheap, nice score. Did you get anything else from him?
Would you care to sell a couple wheels.
How do you like the foot pedal.
 
Saw two of those 056's shorted out from wire insulation peeling where wire goes through case or plate as I remember. Covered wire with shrink wrap and fired both up.

Good call, on the 056 I brought home I already went over old kill switch for any exposed wire and even soldered a new wire onto old ignition as well as trying a new ignition that we got from Stihl, I wish that the 056 I have was as easy a fix as two 056's that you had, that would be awesome. I will update with pics once I start tearing into the old ignition.
 
Not technically on an island but here's one people often overlook when they discuss the 50cc class with the 346 and 550xp, it feels just as light and has nearly 4 hp, its from 1994
That’s a beauty. I’ve only seen one of those in person ever. They just didn’t sell many mid sized huskies up here except for the 51/55.
 
I need to reseach into the 357/357xp? I have a 257. Maybe that’s all I need, not sure yet.

I’m disassembling a husky 44 rancher with the white cover right now.
 
I need to reseach into the 357/357xp? I have a 257. Maybe that’s all I need, not sure yet.

I’m disassembling a husky 44 rancher with the white cover right now.
257 is a good saw, its also got the largest squish of any of the 2 series saws, one of the only ones that you can get away with a base gasket delete on.
Personally I like the 357/359 platform better. Side tensioner, better caps, better air filtration, better AV, way better fuel economy.
Did I say I like the three series better than the 2's :D.
Congrats on the new saw :clap:.
Base gasket delete and a muffler mod does wonders on the 359.
 
Not technically on an island but here's one people often overlook when they discuss the 50cc class with the 346 and 550xp, it feels just as light and has nearly 4 hp, its from 1994
Very nice specimen Derrick :clap:.
That's one of my favorite 2 series saws, little more power than the 346 and quite a bit more grunt, but only a little extra weight.
What's funny is that's the exact saw I've compared to the 550mk2 and what I hoped it would be like. I think the 550mk2 is very similar but with all the features of a modern saw, which some may want more than others. The hp on the 254 iirc was underrated from husky, but independent test showed 4.2, spec check please @SawTroll :).
Heres one I had running a 64dl chain on an old Windsor bar. The video was to show how you can use a bore cut to get under dirt/mud on a log and then cut from the bottom of the muddy spot to throw the mud off rather than pulling it thru the cut which dulls the chain very fast.
 
I’m not sure which series 2 or 3 had the highest max rpm? It’s all about the highest rpm and the lightest weight?

I have two 257’s one will stay stock.

The 346 Xp?

http://www.acresinternet.com/cscc.n...cfb3ee35736aae4688257c97001f8d64?OpenDocument

I have the bigger husky saws sleeping. What a life I’ve had running these awesome saws.
My guess is the 3 series has a higher rpm spec, no its not always about the highest rpm and the lightest weight. There are times especially with regards to the written specs that you won't get a feel for how a saw cuts based in them, as well many times the way those specs are derived are changed through the yrs for various reasons so its hard to make a true assessment based on specs alone.

Not sure what your asking about the 346, great little saws with a diehard following, and while I like them and run them for firewood duties I find the 550 to be much more efficient in all areas for jobs. That being said I like to have the 346s around as they are fun little saws.
 
Wow chipper that 254 sounds good, they have good torque too. I was lookin at the 550xp MII but the demo was too hard to start, plus i have a 2018 550xp that works fine so cant find a good reason to upgrade. I don't notice the higher rpm so much with the small saws but i do with the big saws, especially the new ones, not sure if its really higher rpms but the acceleration of say the 572xp is a lot faster than the 272xp, no big deal since im not using this one anyway
 

Attachments

  • 272xp.jpg
    272xp.jpg
    102.4 KB · Views: 9

Latest posts

Back
Top