Husqvarna 168??????

[jjramrod]

Guy says it's a 168 can't find any info on it at all is he just way off says he just had it serviced seams like shop would of told him what it was

 

[ncfarmboy]

Looks like a 268 to me. Never heard of a 168.
Shep

 

[jjramrod]

Looks like a 268 to me. Never heard of a 168.
Shep

Thanks now that I can find info about

 

[Czed]

268 with muffler mod looks like it to me here's mine

 

[Sepia]

Guy says it's a 168 can't find any info on it at all is he just way off says he just had it serviced seams like shop would of told him what it was

Can you make your pics just a little smaller? I can still just barely make out a chainsaw in the pic... barely.

 

[jjramrod]

Can you make your pics just a little smaller? I can still just barely make out a chainsaw in the pic... barely.

Don't know why two of the three are so small I'll try them again

 

[jjramrod]

268 with muffler mod looks like it to meView attachment 700275 here's mine

Is it a pretty decent saw I'd like to have input from someone that owns one and uses it any idea on value?

 

[eat a peach]

I have 2 of them ,they are very good saws imho. Same series as the 272xp ,268 se and the 268xp.
Under the handle on the clutch side should be a black ID plate . Good luck with the saw .
Check ebay for current selling prices

 

[jjramrod]

I have 2 of them ,they are very good saws imho. Same series as the 272xp ,268 se and the 268xp.
Under the handle on the clutch side should be a black ID plate . Good luck with the saw .

Thanks for the info I saw the plate in the picture looks like it's almost completely stripped looks like bare aluminum probably won't get a chance to see it in person until the end of the week

 

[wcorey]

I dunno, metal tank, frankensaw...
162se or 166 or heated 266 with an aftermarket 272 top cover...?
Id plate would likely be silver.
See if the front top cover screw lines up with the hole in the case.

 

[Chainsaw Jim]

It looks like it could even be as large as a 181se. A pic of the area above the fuel cap would help.

 

[jjramrod]

It looks like it could even be as large as a 181se. A pic of the area above the fuel cap would help.[/QUOTE)

Most likely won't see it until the end of the week so these pictures are all I have to go off of I'm going to try to get him to send me a better picture of that side of the saw

 

[jjramrod]

It looks like it could even be as large as a 181se. A pic of the area above the fuel cap would help.

He just sent me this picture

 

[eat a peach]

Didn't notice the chainbrake, it may very well be a 181,or 266. Both of the ones i have owned had that chainbrake,268,272 didn't.

 

[Ronie]

Here's my old 268SE/XP. It originally had the old style chain break on it and a metal tank like the 162 I sold it for $185. Nice saws with a lot of low rpm power.

 

[Chainsaw Jim]

The location of the av mount screw above the fuel cap is the indicator that it's most likely the 268 as mentioned. The 181 screw is pretty much centered on that square area instead of being near the bottom edge as pictured.

 

[jjramrod]

Thanks for the info he wants 280 for it so I guess I'll just pass on this one

 

[Ronie]

That's way too much.

 

[ncfarmboy]

That's way to much.

Agree! pass on down the road.
Shep

 

[jjramrod]

Ok new question I have two 3120s to look at one supposedly only needs a coil and the other one is kinda tore apart powerhead is still together but tank and handle are off what tools will I need to bring with me to remove the mufflers to check the Pistons and what would these be worth assuming they don't need cylinder and pistons replaced no bars just power heads