Wow didn’t know Birch got that big
Let’s see the homemade Alaskan chainsaw mills!
- Thread starter motolife313
- Start date
Help Support Arborist Forum:
Yea, there are birch in my area “Anchorage Alaska” and more specifically the Mat-is valley that get over 20” in diameter. The one in the pictures was 22” at the base.
Eric Vogus
ArboristSite Member
These are from Petersville. I live in Wasilla.
Attachments
Clifwoodman
ArboristSite Lurker
Clifwoodman
ArboristSite Lurker
That’s mine whilst waiting on Panther mill! Not much but does the job!
It's not exactly home-made, but it is home-modified. I used a $100 Chinese Grandberg knock-off for parts and rebuilt it with longer, heavier extrusions to fit the 36" bar on my 084. I had to run them through my other mill (ie: metal milling machine) to rabbit one edge on each, but the result is very sturdy.
I bought 2 Stihl .404 ripping chains. Seems to leave a decent finish. I didn't use a stopwatch, but it cuts a 10' length in Red Oak and Maple in about 5 minutes.
I hit a couple of hidden nails in the centre of one log. Surprisingly little damage to the chain, just a little kick that made me think "what was that?" It didn't even slow down for the rest of the cut. But I decided to switch to a carbide cross-cut chain for the next cut. Not gonna do that again! Terrible finish and very slow. I'll save the carbide chain for cutting off the stumps near ground level in the future.
The problem with this thing is that everyone else wants to try it out too!
After reading what others have done, I think future mods may include removing the rollers in place of the skids and a winch. Removing the bucking spikes and switching to the one-bolt method of mounting to the bar would not only maximize length, but also make it a lot easier to change chains. Does anyone know if the Stihl 3-foot sprocket nose bar is a suitable candidate for drilling the centre of the sprocket?
In the interests of full disclosure, this is not my first foray into chainsaw milling. My first attempt was 18 or 20 years ago, freehand, with my only saw at the time: a 16" bar on an 025 with a chain modified in what I thought was a suitable imitation of a ripping chain. I knew nothing about grind angles, I just ground the tops off alternating pairs of teeth.
The results were not pretty. No photos exist.
However, after much clean up with the bandsaw, jointer and planer and lathe, I turned that beech and oak into a staircase. And many, many bags of sawdust!
I bought 2 Stihl .404 ripping chains. Seems to leave a decent finish. I didn't use a stopwatch, but it cuts a 10' length in Red Oak and Maple in about 5 minutes.
I hit a couple of hidden nails in the centre of one log. Surprisingly little damage to the chain, just a little kick that made me think "what was that?" It didn't even slow down for the rest of the cut. But I decided to switch to a carbide cross-cut chain for the next cut. Not gonna do that again! Terrible finish and very slow. I'll save the carbide chain for cutting off the stumps near ground level in the future.
The problem with this thing is that everyone else wants to try it out too!
After reading what others have done, I think future mods may include removing the rollers in place of the skids and a winch. Removing the bucking spikes and switching to the one-bolt method of mounting to the bar would not only maximize length, but also make it a lot easier to change chains. Does anyone know if the Stihl 3-foot sprocket nose bar is a suitable candidate for drilling the centre of the sprocket?
In the interests of full disclosure, this is not my first foray into chainsaw milling. My first attempt was 18 or 20 years ago, freehand, with my only saw at the time: a 16" bar on an 025 with a chain modified in what I thought was a suitable imitation of a ripping chain. I knew nothing about grind angles, I just ground the tops off alternating pairs of teeth.
The results were not pretty. No photos exist.
However, after much clean up with the bandsaw, jointer and planer and lathe, I turned that beech and oak into a staircase. And many, many bags of sawdust!
brianpoundingnails
ArboristSite Lurker
Here's mine. Combination chainsaw mill, mortiser, lathe, drill press. Dropbox link for more pics.
machine: https://www.dropbox.com/sh/nr4yw91iv2hgdl0/AACv5-Unq_KSGyYK-2YHwWIBa?dl=0
furniture: https://www.dropbox.com/sh/pq9hfk8rqr7l416/AADQZxeku_HGeIBLpz4MeasIa?dl=0
machine: https://www.dropbox.com/sh/nr4yw91iv2hgdl0/AACv5-Unq_KSGyYK-2YHwWIBa?dl=0
furniture: https://www.dropbox.com/sh/pq9hfk8rqr7l416/AADQZxeku_HGeIBLpz4MeasIa?dl=0
Attachments
earlthegoat2
ArboristSite Guru
My simplistic but IMO improvement over the Granberg Mk3. 1” steel construction. Thickness of cut is secured with double set screws. Only disadvantage of note is the setup time for different thicknesses. I want to make some spacer blocks to remedy this.
Built to handle a 36” bar and 29” total cut width. Shown here with a 32” bar.
Built to handle a 36” bar and 29” total cut width. Shown here with a 32” bar.
Eric Vogus
ArboristSite Member
Wow nice unit. I like that a lot.
Eric Vogus
ArboristSite Member
Eric Vogus
ArboristSite Member
Wow nice looking unit. Well done.
goncalo alves
ArboristSite Lurker
I'm buying my first one but I like tracking these. Anyone else have a homebrew?
Similar threads
