Want to Sell Zogger benefit auction,MMWS ported Makita 6401

[Deleted member 149229]

Some of us are trying to raise some money to help out Zogger who recently had some extensive cancer surgery. I’m donating this Makita 6401, pho only, it does have the high performance smurf sticker. I bought it a few months ago from Brett, @chipper1. I’ve only run 1 tank of fuel thru it, no problems, just have too many saws. Saw has been ported by MasterMind, Randy. Any questions about saw ask Brett, I think it had some port work. Opening bid is $300, minimum bid increase is $10. I cover shipping to lower 48 only. Auction closes at 7 PM eastern on Oct. 5. All money from the saw goes to Zogger. Payment to be made thru PayPal Friends and Family. Please make all bids thru the thread so there is a record of who, amount and when.

 

[svk]

Very generous of you! I am going to set up an official Zogger thread as well.

 

[svk]

@Dahmer, what is the minimum bid increase? Maybe $5 or ten above previous bid? Can you please put that in the description as well?

 

[Deleted member 149229]

@Dahmer, what is the minimum bid increase? Maybe $5 or ten above previous bid? Can you please put that in the description as well?

Good thinking. Done, minimum bid increase is $10.

 

[svk]

I'll open bidding at 300 for this

 

[ammoaddict]

Good thinking. Done, minimum bid increase is $10.

Very generous of you sir, to give up your Smurf saw. You all are a bunch of great guys.

Sent from my Moto G (4) using Tapatalk

 

[chipper1]

When I bought the saw I was told it was ported by Randy. I never had the muffler off the saw to look at the porting. I do know it had a poleman carb on it. I sold it because I bought another ported 7900, I never had a problem with it, it always fired right up and did what I asked her too.
She had an HD filter kit on it in these pictures(it didn't have the smurf sticker then either ). I think this was my last outing with it.

 

[Deleted member 149229]

When I bought the saw I was told it was ported by Randy. I never had the muffler off the saw to look at the porting. I do know it had a poleman carb on it. I sold it because I bought another ported 7900, I never had a problem with it, it always fired right up and did what I asked her too.
She had an HD filter kit on it in these pictures(it didn't have the surf sticker then either ). I think this was my last outing with it.

Thanks Brett.

 

[Armbru84]

310

 

[Deleted member 149229]

@Armbru84 is high bidder at $310. Thank you sir.

 

[svk]

@Dahmer if it still allows you to edit the title, you might want to add that it was ported by Mastermind, as I hear he has quite a following on the net.

 

[cuinrearview]

$350

 

[Hdtoolmkr765]

$400

 

[Hdtoolmkr765]

$350

Sorry Tim, I have one spot left on my Dolly shelf and my two 5100s and 7910 are feeling a little outnumbered by the Stihls and Huskys.

 

[cuinrearview]

Sorry Tim, I have one spot left on my Dolly shelf and my two 5100s and 7910 are feeling a little outnumbered by the Stihls and Huskys.

Ain't no thing Brad, plenty of them out there. All for a good cause.

 

[bowtechmadman]

420.00 I don't have a blue saw.

 

[Deleted member 149229]

@bowtechmadman is high bidder at $420. Thank you sir.

 

[Deleted member 149229]

TTT

 

[Deleted member 149229]

TTT

 

[svk]

Bump, 96 hours to go. Remember this is a very nice saw and ported by Mastermind