• Please be aware that we have recently gotten a wave of users that, when researched, are found to be from Nigeria. They are trying to sell products and asking to be paid through Zelle or Venmo leaving users with no recourse if they don't ship the product. If you suspect this activity please contact admin and we will research their information to verify their location.

ArboristSite.com Sponsors


Search results

  1. stilh036prohog

    Husvarana 55

    This big cedar had anchors in it. Old for the s east. Can y upgrade the pump ?
  2. stilh036prohog

    Husvarana 55

    Is there an upgrade to the oil pump? I'm running a 20 and it's a little weak. The 281 is fine.
  3. stilh036prohog

    Stihl RS, Oregon LPX, Carlton Full Chisel

    I run Oregon exl now because it cuts good and get at cost from buddy
  4. stilh036prohog

    Sunoco race fuel?

    The 100ll last longer in storage.
  5. stilh036prohog

    Sunoco race fuel?

    Yes they have lead and no leadl up to 115 I think.
  6. stilh036prohog

    Sunoco race fuel?

  7. stilh036prohog

    Sunoco race fuel?

    Does anyone run this stuff? I use to run 100ll that I got from the airport I worked at. You had to retune your saws thou. It lasted longer then pump gas. This isn't an oil thread but gas. Maybe in a hot saw. Just thinking?
  8. stilh036prohog

    Stihl 046

    Try a husky 281. Pull it until it's right past tdc and give a good pull. I still have the scar trying to start my 281.
  9. stilh036prohog

    Poulan pro 405 bar?

    I just like the sound of the reed valve engines. That 041 kept us warm for many years. My dad brought it new in the 80s. My first saw I rebuilt. I'm impressed with 405 for sure. Looking for an old echo to go with it.
  10. stilh036prohog

    Poulan pro 405 bar?

    Well I got a chance to put in some big red oak yesterday, man it pulled that 24 just fine. My Stihl 271 didn't have the balls like these old reed valve engines. Kinda like my 041. Me likes.
  11. stilh036prohog

    Mildly annoying events today

    Dang my day was better. Good that the whole shop didn't burn. What do you need?
  12. stilh036prohog

    Stihl 034 Ring End Gap.

    Is the cylinder good if not make it a 036.
  13. stilh036prohog

    Stihl 034 Ring End Gap.

    That saw ,then just reused them. I use new rings whenever I pull the jug. I hope she will for you Tom.
  14. stilh036prohog

    How do I tell whether my saw takes a narrow kerf chain?

    Post a pic of your bar numbers. That will help us.
  15. stilh036prohog

    Poulan pro 405 bar?

    I filed down the bar and made it fit. Hope to put it some wood today. I hope it pulls that 24.
  16. stilh036prohog

    Stihl 034 Ring End Gap.

    Don't do it
  17. stilh036prohog

    Stihl 034 Ring End Gap.

    Oh nice work on the mag rot. Looks good. ? What time is it there.
  18. stilh036prohog

    Stihl 034 Ring End Gap.

    That's I good question. I just looked in my manual and I didn't see it either. Can't remember what I used when I rebuilt my 036. Is a new piston and rings ?
  19. stilh036prohog

    Poulan pro 405 bar?

    Me to it was a tight fit for sure. I haven't ran the saw with the bar on it. I'm just going to file the slot to make it fit. It's a good running saw, sounds mean. It pumps oil fine. Mm how do you like these saws?
  20. stilh036prohog

    Poulan pro 405 bar?

    Just picked this up and he said it not oiling right. It came with almost new woodlanpro timbermax bar with the number wptm 24 hu50 f8 stamp on it. I had to pry the bar off because it was tight on the the studs. The saw runs and pumps oil. I think the bar is wrong. In my research I did not find...
Top