ArboristSite.com Sponsors


Search results

  1. Jethro 2t sniffer

    The unofficial Mac 10-10 thread

    Yeah we see all kinds of muffler mods and repairs to these saws the mods are usually to make it quieter lol. Your right it could be fairly lucrative youd think. Especially now the popularity is going upwards
  2. Jethro 2t sniffer

    McCulloch Chain Saws

    Haha ya don't have to hit it very hard
  3. Jethro 2t sniffer

    The unofficial Mac 10-10 thread

    Interesting muffler fix. Yeah the filters are a bummer unfortunately:( I'm looking to patch 1 up also
  4. Jethro 2t sniffer

    The unofficial Mac 10-10 thread

    That's the domed air filter unfortunately you will get a whole saw for the price of those but yeah Ebay. If you have a few holes in yours use a bit of silicone or hot glue or something to plug the holes up or glue a patch of something over it. I've heard of vacuum cleaner filters. Bar size in...
  5. Jethro 2t sniffer

    McCulloch Chain Saws

    Good luck on the 850 lol the 10-10 be easy enough. Put an add in the trading post. I take it you're after any 10 series? Good saws be patient you'll wind up with a heap in a few months. I say good luck on the 82cc as we all love ours:)
  6. Jethro 2t sniffer

    McCulloch Chain Saws

    Got the nut off? wind the nut back on but keep the crank below flush now grab it by the clutch and hold up the saw so all its weight is hanging by the clutch now give that nut a wack or two with a hammer a soft copper hammer preferably but if nice and square a regular hammer will be ok. The saw...
  7. Jethro 2t sniffer

    Remington or Poulan

    https://www.arboristsite.com/community/threads/poulan-4000.341309/#post-7243541
  8. Jethro 2t sniffer

    McCulloch Chain Saws

    Also it's a keyed clutch too so can't really give it a little extra jandel on the rattle gun or pop it will go. Still think the dremel will cut a good enough key way
  9. Jethro 2t sniffer

    McCulloch Chain Saws

    Hmm maybe the dremel might be the way then. I can always try it. Theory says the taper should hold it but they put a key in there for a reason
  10. Jethro 2t sniffer

    McCulloch Chain Saws

    Ok cheers Mark. I'm seriously considering putting my spare 700 engine under the 2-10 covers. If its an issue I could cut a key way with a dremel
  11. Jethro 2t sniffer

    McCulloch Chain Saws

    Thanks Todd I'll look them up
  12. Jethro 2t sniffer

    McCulloch Chain Saws

    I think that might work the 8mm should squeeze down around the edges and hopefully seal up. On the older 60s and early 70s 10 series Todd they have a "domed" filter and are very pricey. I run or will run two of these 1 is ok the other will be saveable just but not forever so diy is starting to...
  13. Jethro 2t sniffer

    McCulloch Chain Saws

    Mark will a right hand start stay tight on a non keyed clutch? Eg later crank
  14. Jethro 2t sniffer

    McCulloch Chain Saws

    How thick is the yellow layer? I'm wondering if that could be hot glued to some wire mesh and fit under our lids
  15. Jethro 2t sniffer

    Close call

    Thank you for the lesson. I think you did real good in the big scheme of it all. Enjoy the holiday:)
  16. Jethro 2t sniffer

    McCulloch Chain Saws

    Can't wait to see that thing going when the wood fun begins:)
  17. Jethro 2t sniffer

    McCulloch Chain Saws

    Good effort on the fuel line
  18. Jethro 2t sniffer

    Poulan thread

    Dam that's alot of noodling Thanks Todd
  19. Jethro 2t sniffer

    Poulan thread

    You know for 98cc its actually a nice weight really. Google says the 395 is 17.4 I had an itch this morning so went and cut a second side port in the orange 4000. Sounds nice now just a little deeper tone than the two pipes could also be the brake changing the sound too Bars buried there both...
  20. Jethro 2t sniffer

    McCulloch Chain Saws

    Haha yeah I only reached down to pull a silly little stick out and.. sssssssss lol after that I understood why the muffler cover was added
Top