ArboristSite.com Sponsors


Search results

  1. tmessenger

    SOLD!!!! Real nice Stihl 032 with two bars and chains

    I sold one last year on facebook (cleaner then yours) with an 18" bar and new chain for $175 so I think you are more or less in the ball park. This might be a tough crowd to sell to unless it is "collector quality", even the 028's are getting harder to sell.
  2. tmessenger

    Want to buy Stihl 028 oil pump, pump cover and clutch hub bearing.

    Too rich for me for this old saw but thanks for the offer. Tim
  3. tmessenger

    Want to buy Stihl 028 oil pump, pump cover and clutch hub bearing.

    Let me know what you want for the parts shipped to 52556. Note the pump has a small oil seal pressed into the body is it still in good condition ? Thanks Tim
  4. tmessenger

    Swap meet...

    I need a good 028 oil pump with the drive gear (don't need the small one that the clutch drives) the plastic pump cover, the long double row needle bearing for the clutch hub and the bell shaped washer that holds the chainbrake handle on the starter housing side. Shipping would be to Iowa 52556...
  5. tmessenger

    Want to buy Stihl 028 oil pump, pump cover and clutch hub bearing.

    still looking for these parts.
  6. tmessenger

    Want to buy Stihl 028 oil pump, pump cover and clutch hub bearing.

    I need a good 028 oil pump with the drive gear (don't need the small one that the clutch drives) the plastic pump cover, the long double row needle bearing for the clutch hub and the bell shaped washer that holds the chainbrake handle on the starter housing side. Shipping would be to Iowa...
  7. tmessenger

    Want to Sell SOLD Stihl 026 project

    Clean 026 this is the one with the fully adjustable carb. Piston shows light scoring but still has good compression, does the slow fall when hung by the rope. Sorry my conpression gauge is no longer in calabration so can't provide a number. Does not want to idle down so a vaccume leak...
  8. tmessenger

    Best goop to repair plastic threads

    Stick a lenght of string trimmer line in the hole then thread in the bolt.
  9. tmessenger

    SOLD!!!! 028AV woodboss. $150

    I think we all know what's going on here, there is a diaphragm in the carb that runs off of impulse that's how gas is drawn out of the tank below it is a fuel pump, yes? On the Woodboss it says electronic quick stop us saw nerds all know this means electronic ignition and chain brake but not...
  10. tmessenger

    Vintage Chainsaw Collectors Lounge

    Right around 12" to the outside of the handle bar to the outside of the clutch cover.
  11. tmessenger

    Vintage Chainsaw Collectors Lounge

    HOE was a USA importer for Partner saws back in the late 50's early 60's, not a lot of info available on the importer but the Partner R11 was common enough at least in Europe. The first R11 had a straight rear handle with a thumb throttle like this one the later version has a more standard...
  12. tmessenger

    Partner R11 parts need and other general questions.

    I picked up a Partner R11 this week I believe it's one that was distributed by HOE in the USA as I can see where the Partner cast name was machined off the top of the starter housing. This one the coil was dead but I took the coil part way apart (the coil is not potted in epoxy like a modern...
  13. tmessenger

    SOLD!!!! Stihl MS 170

    You might want to check the price of these new to help you put a value on it?
  14. tmessenger

    SOLD!!!! Total Super 20" Bar Husky Mount.

    Nice condition 20" bar 3/8 .050g D009 mount part # T417FV4 slots are tight and tip is good . $28 net to me you pay shipping and pp fee. Shipping weight is going to be 4 pounds and ships from zip 52556.
  15. tmessenger

    Where could I get the most money for a saw I dont want?

    I sold a fresh reconditioned 028 Wood Boss last fall on craigslist spotless clean new 16" bar and chain + used 18" B/C it took a couple months to sell @ $250.00. For $300 I would think your saw needs to be collector quality or close to it, so add photos and we can evaluate.
  16. tmessenger

    Where could I get the most money for a saw I dont want?

    I've sold two saws on craigslist in the last week (Jonsered 2159 and mint John Deere 50V) they were clean, well tuned and I was not trying to squeeze every dime out of them. I see saws on craigslist in my area all the time with stupid money asking prices. I've also had good luck selling on...
  17. tmessenger

    Want to Sell Stihl 032 complete coil / ignition

    This was from a saw with a scored cylinder coil tested good with hot spark. Points are a little pitted but could easily be cleaned up. $50 shipped in USA. Tim
  18. tmessenger

    John Deere survivor, nothing runs or weighs like a Deere.

    "If I was you, start stopping by the Lamborghini dealer once or twice a week too." Well not a Lamborghini will a Triumph work? Last winters project this one had been sitting in dry storage and hadn't moved for 37 years. Needed a lot of help but now is my daily driver, I can get a couple of...
  19. tmessenger

    John Deere survivor, nothing runs or weighs like a Deere.

    It was laying outside at a saw shop last week and was still in the same place when I was there today, they were using it to cut up pallets on occasion and were happy to see it go.
  20. tmessenger

    John Deere survivor, nothing runs or weighs like a Deere.

    I really didn't need this to follow me home but............ John Deere (Echo) 50V 44.3 cc of two stroke venom. Tame them woods boy if you are man enough! And man enough means 13 1/4 pounds for a dry power head, I think I could sell this for scrap and make money. It is kind of cute, don't...
Top