Search results

Arborist Forum

Help Support Arborist Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. M

    Facebook buy, sell or trade chainsaw and parts groups

    Got a Dolmar 421 for 75 bucks cash on Facebook. Funny story guy had it for a 150 which was a good deal asked him some questions about it. I already had bought a brand new one of a guy on here few months before didn't really need another one. Guy called back two weeks latter wondered if I would...
  2. M

    My chainsaw doesn't get any fuel (I think)

    Douch it with premix real good if you didn't have a rag stuffed around the crank you don't want shavings floating around no Bono. May need a longer allen bolt or wider.
  3. M

    Mix ratios on Echo equipment

    I run 50-1 with Amsoil Sabre and 40-1 with everything else which is usually Red Armour.
  4. M

    Dolmar 421problem

    I bought the 421 off of Wood butcher love the saw 2 pulls and she goes runs awesome dare I say it I like it better than the johnsered 2253 of course the 2253 has more snot but I love that 421 runs awesome
  5. M

    Jonsered 2036 turbo running problems.

    I went down the same rabbit hole buddy had it was a close out and never ran it chain was on backwards from the store it was that little grommet that goes on the plastic divider pipe to the cylinder so it wasn't getting any draw
  6. M

    Jonsered 2036 turbo running problems.

    Just worked on 1 of these the plastic part the carb mounts to has a rubber grommet that goes from it to the cylinder they go bad and suck air and you can't tune the carb afleetcommand has a video about it the grommet is like 6 bucks
  7. M

    Chainsaw won't start 3 REASONS why!

    It's called Banter and hat bills go in front unease operating vehicles without windshields Aka racing mode
  8. M

    Chainsaw won't start 3 REASONS why!

    I've gone to GTG and have witnessed the tuning abilities of some of the guys on here that's why it's good to sit back and listen sometimes and there is alot of misinformation on the youtubes. I have watched a guys racing saws and one of the guys said better check your gas it was going lean in...
  9. M

    HUSKY 359 squish?

    Thanks soon as piston comes in I'm going to be at it
  10. M

    HUSKY 359 squish?

    Would like to run a gasket have Mills and lathes available. What would be a good number for the squish have all the parts for rebuild but the Meteor piston and rings . Will it be a different squish between two different pistons? Also have die grinders and many carbide bits can I get some tips...
  11. M

    Give it to me straight on ported saws 346xp DD

    Dozer Dan ported my 365xt and I bought it new from him and had him port it and remove transfers I have had know problems you could try getting a hold of him he knows his stuff. He's in bad health and don't port buy did a good job
  12. M

    390xp Highspeed problem

    Coil is probably rev limited.
  13. M

    Husky 350 chain sharpening

    Need to know what chain hes running
  14. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    Isn't it fun saw shopping with other peoples money . Buy the 395 if you don't like you can always get another saw tell the wife it's ro heavy need a smaller one.
  15. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    A 461 would be a good one a Dolmar 7910 isn't a bad one either
  16. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    That's cool I'm know wimp but you better pack a lunch to run one all day. Tater Wade runs one but that's what he does for a living his side kick Stevie does also but they run them all the time
  17. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    Contact F150 on hear he's in Ohio he fixed my saw the johnsered 2253 that was at 3 other shops he carrys johnsered, echo and Makita and he knows his stuff call him he won't steer you wrong
  18. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    A husky 562 new models that are sorted out our a 620 Echo or Makita equivalent I have a 550xp and would rather have something you can tune than tune itself
  19. M

    Husqvarna 390XP vs 395XP ...which one is the better saw?

    Buy a 365xt and have it ported price will be cheaper and a low top and you can run a 28 inch bar if you want to no problems I run a 20 or 24 full chisal
  20. M

    359 Husky Rebuild

    Cuinrearview slingers shot the pumps tied up but I'm thinking I can get it working again. I may just order a slinger when I order the ring and gasket set. And you are right they think the pumps are gold.
Back
Top