Search results
Help Support Arborist Forum:
-
H
New to 4cycle
Linkage is hooked up and works as it should and the only adjustment is idle speed.New carb on the way Sent from my LM-Q710.FG using Tapatalk- hayseed79
- Post #3
- Forum: Hand Held Equipment and Tools
-
H
What string trimmer to get
Husky 525rx works good.Really easy on gas. Sent from my LM-Q710.FG using Tapatalk- hayseed79
- Post #2
- Forum: Hand Held Equipment and Tools
-
H
New to 4cycle
I got a cub cadet cc4125 weed eater thats 4 cycle and it won't accelerate.I have replaced the fuel lines,fuel filter,air filter rebuilt the carb.Its like its not getting fuel.If I press the primer bulb it will rev up then go back to an idle.Any suggestions? Sent from my LM-Q710.FG using Tapatalk- hayseed79
- Thread
- Replies: 2
- Forum: Hand Held Equipment and Tools
-
H
Husqvarna 36 flooding help
This will make a huge difference Sent from my LM-Q710.FG using Tapatalk -
H
Carbides, port tool recomendations.
1/8 inch Carbide Burr Set - 10pcs... https://www.amazon.com/dp/B073CHWZX8?ref=ppx_pop_mob_ap_share....I used these on a couple cylinders and I'm happy with the results Sent from my LM-Q710.FG using Tapatalk -
H
Shindiawa 488
So I gave the 488 a very aggressive muffler mod and a 3/8 LP chain and I gotta say I'm liking it!!!I want to weigh the 488 and my 36 husky.. I'm betting on they are close and thats an 18" bar on the 488 and a 16" on the husky!! Sent from my LM-Q710.FG using Tapatalk -
H
Worth fixing?
Watched Buckin keep up with a 372 with a Mac 81!! Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
When I put the 4 bolts in the pan and draw them down the pan and cylinder mating surfaces are touching so no matter how it's done they can never get any tighter...if I'm understanding you right?...but if I was to sand a few thou off the pan flange that would gain me squeeze as long as a have... -
H
Can't pass the test
Sometimes drying overnight has things stuck fast in the morning Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Gave it 24 hours to dry per directions... Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Skf seals and bearings and I did try putting yamabond around the seal the 2nd time Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Leaks where the seal meets the case...everything looks good just won't seal....I missed corn beef and cabbage this year. Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Ham potpie Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Advice is what we are here for.I just did ham pot pie but the dogs sound yummy Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Supper Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Pics of the saw Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Soon as I eat Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
New bearings too Sent from my LM-Q710.FG using Tapatalk -
H
Can't pass the test
Correct Sent from my LM-Q710.FG using Tapatalk