Search results

What are your thoughts?

Had a chance to get a 881 on the dyno. Let me know what you think.

Ran all the saws today... In this order 572xp 7310p 7900 500i 462 Some showed up, some were lacking. This is a comparison..... Hp/tq are what were measured today. Every saw had 6 pulls made, and the avg run was selected for display. All runs were corrected to the same...

Full rebuild, split case, new bearings, rings, seals fuel/impulse lines. Modified carb. 620 coil, rim drum setup, outer spike. Basically a ported 620, with a plastic handlebar. Not a beauty queen by any means. Good solid firewood saw. Less than 3 tanks on it. 425+ship with 620 coil 350+ship...

Looking to buy a complete cs5000 running or not. If you have one let me know.

Getting out of the 2 series saws. Would like to trade for a 395, complete/builder/project. Stock saw. Fresh ported 268, case with 272 top end. From zoo city saws. Termitebuffet. Completely rebuilt, new bearings seals everything. Less than 1 tank Asking 475 shipped. 288xp completely...

Looking to sell my ported husqvarna 350. Have about 5-7 tanks through it. Base cut, squish set at .017. Full woods port, nothing radical. WEM 44.3 346 aftermarket cylinder meteor piston, caber rings metal intake clamp. 346 muffler brace New bearings/seals, intake boot, Treemonkey'ed...

Nice saw runs cuts oils, 16" picco bar chain. Used it to trim a few branches. Have no real use for it. Would like to get 400$ shipped Or possible trade for husqvarna 3 series 357,359, or 385,390 builders project saw.

Looking for the clutch side crankcase for a 346 351 353. Let me know what you have. Thank you

Well got the 350 under my belt, now to try something "pro grade" Saw came from auction no known history. Started right up cut oiled good. 150 comp Going to swap this out.. Though it would have been unlimited being a 99 Intake side of the piston (notice no locating pin) Exhaust...

1st Poulan 3300 passed the drop test Piston looks good $50 + shipping PHO Craftsman 3.3 couple light marks on piston, still decent compression. $50+shipping more 3.3 3300 parts $75+ship Poulan pro 335 $40 + Ship will trade for Husqvarna 340-50 not really...

Made this, Cut this Made this to finish the squish once I get the case ready. WEM 44.3 346xp husky 350 Project. Feedback much appreciated A smaller lathe would be handy.

Homelite xp 1020 auto. new in last 8 months fuel line/filter and a carb kit Runs, cuts, oils could use a new clutch spur. .404x8 PHO $250+ship Next Homelite sxl 923 new lines fuel filter and carb kit 3/8 x 7 runs cuts oils $200+ship PHO

Looking for a badly scored, non serviceable Husqvarna 272 P/C 52mm bore If you have anything let me know Thank you

Started out like this Then something squished them Look to be 18 gauge steel really similar to the black Husqvarna 288 part Cant for the life of me figure out what they are for? Anybody know? would 20 gauge stainless make them better?

Got out of work early today, itching to play with my new saw ms261c. I grabbed dads ms241c 14" picco chisel, so I could make sure I made the right choice This is the first time I have ever cut wood without a homelite:cry: Needless to say they were not missed much. Filled the tank with the...

I have been whining about missing all of the good deals in the trading post, I guess she got tired of listening, and my birthday was the 31st and we both had to work, so she said you don't get anything until after the holidays. Well, I got home today, and my girlfriend said lets go get your...

I am going to be In the market for a new firewood saw. Just wanted to hear some opinions. What is your favorite 1 saw 60cc and under for getting firewood? Lets say 18" and smaller whole trees. List bar length and chain type. And pros/ cons about the model. ONLY 1 saw this time fella's...

Ok Now that I have your attention. I am looking for pictures of your Headache rack, truck rack anti smashed window device whatever you choose to call it. I would like to see some pictures. Thank you Joe

A full std cord is 4x4x8 correct? I chopped a couple limb off of a field oak and I think I am close to 3/4 cord in this load. Does that sound about right? This is my 2nd season of burning I am trying to keep track of wood used this year. Thank you Joe