Search results

Here is last year's post from Bob @Farley9n, which Jim copied and pasted for the 0-P-E thread. He edited the dates accordingly. "The mostly annual Pacific Northwest GTG will be taking place between the 8th to the 11th of June. There will be a couple of work crews a bit before. The location is...

Like it says, I'm looking for crank bearings 504 2300 12 for a Jonsereds 111S, qty 2. I believe the bearings cross with the 910. The faster I find these and get the saw fixed, the faster I can sell it to @bulletpruf ;) Cross-posted in the Jonsereds thread. Thanks!!

Looking for NOS or aftermarket crank bearing PN 56097-S and gasket 55048-A for a 775G that is getting rebuilt for my dad. I have the other side bearing and seal. Cross-posted in the Homelite thread. Thanks!!

Seriously contemplating getting one. Word is they're the bees knees for t-posts etc. Anyone have any experience with these?

I'm gonna be holding a one-day prep rally at my place a week or two before the GTG at Bob's,either Sat May 27th or Sat June 3rd (depending on attendee feedback.) Located about 25min NW of Hillsboro. Shoot me a PM for details. Barnyard is set and there are more logs available. Maybe even...

1 ea of PN's 503 26 02-09 (NLA) and 503 26 02-10 (supposedly available.) If anyone has any for sale, I' rather support a member.

Sent this to a friend. He felt strongly that it should be posted up for the enjoyment of all. Not sure if it's been around before. But there it is.

I have a 2036 with a non-functioning chain-brake. I started looking into it, and it seems that I am not the first person to go digging around in there. It is missing the compression spring and a couple of pins. If anyone has a junked out 2036 or 2040 with a working chain-brake, I'd be...

Just got a 044 12mm from @sawfun . Now I need a bar, and I'd rather support a fellow member than an Ebay stranger. I'd like a Rollo-ES if possible, but I do have a thing for NOS Sandviks from :bowdown:@Jon1212 No China, please.

Need a new oiler for my Jred 80. I believe the 621, 80, and 90 oilers are all the same. My saw is currently blowing chain oil like a bug fogger......

Standing dead oak at a friend's house. @sawfun and @medic5050 were along to get in on the action. I made the face cut with my 70E, and the back cut with Don's ported 372XPW. Dropped perfectly down the alley. Dressed out for the occasion was my 111S, 70E, and 034AVS, Don's ported 395, 372...

I just bought a 1982 F150 4x4 with a 300-6, SROD 4spd, NP208 (I think.) I want to get rid of this POS transmission and swap in either a T18/19 or NP435. I've been perusing the Ford forums, but there is SOOOOOO much information there that it is almost impossible to find anything. There are...

Some time ago I purchased from @sawfun a Jonsereds 80 with a Jonsereds 90 P&C. A short time later, I purchased a spare Jreds 90 P&C from @Flat47 . I'm thinking about having this spare set ported. My question is, would a specialist need the whole saw, or can this be done shipping only the...

The headgasket popped on my wife's 1990 Isuzu Trooper last May. We decided at the time to completely rebuild it to be her Adventure Vehicle. I tore out the 2.6L motor, stripped it down, and brought it to a machinist. It got bored over .020", fully balanced, and a custom camshaft grind to...

I've been doing a little searching and I can't find any posts about the best way to reclaim the fuel and oil is a saw when one wished to drain said saw of fuel and oil. The obvious process is: 1. Remove fuel cap. 2. Invert saw, pouring fuel into large catch vessel. 3. Pour fuel from catch...

I'm looking to build up a Mac 55 with a 70cc jug for my dad's Christmas present. If anyone has a spare P/C from a 700, I'd like to make an offer.

I just got my 70E in and am looking to replace the old 20" Sandvik that came with it. I've been reading through posts on bars for the 70E. I see that the "correct" mount is D024, 10mm slot. I also see that some bars will mount with a widening of the <10mm slot, and some bars will mount with...

Ebay grab for $150 shipped! Only downside was that the seller forgot to empty it of gas/oil. Considering how much was all over the inside of the box, and how much the package STANK, I am surprised Fedex didn't call the bomb squad. I got it home and wiped it down, specifically drying off the...

I just picked up another 52E on EBay..... @Cantdog : any known upgrades for this guy? Bigger P/C perhaps? Yeah, y'all gave me CAD. Specifically @sawfun . I blame Don for this. ;)

I want to get a new bar for my 52E, but am a little overwhelmed by all the choices. @sawfun set it up with a 3/8 floating rim sprocket, and I definitely want to keep a 3/8 chain. He recommended Total, Tsumura, or Sugihara. These all seem like great choices, but I am reading about all sorts of...