Search results

Hi Guys, I have a customers Jonsered CS2147 (Husqvarna 346XP) that came in for a full strip-down and rebuild. New piston & cylinder, plus every seal, gasket, hose, intake boot, bearings etc were replaced (all genuine OEM parts). The Zama carby was also rebuilt. Once assembled, it was pressure...

Hi Guys, I have a customers Jonsered CS2147 (Husqvarna 346XP) that came in for a full strip-down and rebuild. New piston & cylinder, plus every seal, gasket, hose, intake boot, bearings etc were replaced (all genuine OEM parts). The Zama carby was also rebuilt. Once assembled, it was pressure...

Thanks for the replies. I'm staggered that you guys pay round US$300 per spool (approximately AU$375) for Stihl chain. The list price for a 100' spool of Stihl over here is AU$970, which is approximately US$705.

If you hear a soft gentle hum overhead don't panic (indeed you won't have time to panic), as the drone will release it's guided missile momentarily afterwards. The secrets of starter cord sizes is only revealed to selected few deemed worthy to carry forth those secrets from one generation to...

Just wondering if you still have the 3/8 x 063 Rapid Micro for sale please? Shipping would be to Oregon PM me with price and postage if still available

Look I'm aware that Stihl chain is expensive here in Australia, in fact there has been two massive price hikes this year alone. In the past buying in bulk 100' spools did afford you some substantial reduction, however Stihl appear to have recently pushed spool prices through the roof over here...

Looking for an OEM Stihl MS361 crankshaft in excellent condition. Shipping is to Oregon USA.

I have a 394XP near complete (no piston or cylinder) which the owner has told me to sell. I don't think he wants much for the saw. Shipping the whole saw to the US may be a bit expensive, so if you give me a list of what you need and I'll try to help out.

Wish to purchase a good condition OEM Husqvarna cylinder to suit a 395XP for an experimental project. Don't mind if it has a few light marks in the bore, but no deep scratches or gouges. Also no cracked or broken cooling fins. Shipping is to Oregon USA.

Wish to purchase a good condition OEM Stihl cylinder to suit an MS880 - 088 for an experimental project. Must suit the older style clip-on muffler. Don't mind if it has a few light marks in the bore, but no deep scratches or gouges. Also no cracked or broken cooling fins. Shipping is to Oregon...

Thanks for all the assistance guys it was greatly appreciated. After a suggestion from fearofpavement, it turned out the spur sprocket kit supplied had the correct part number, but for the later series Model 40, as opposed to the early series saw I was working on. There was a minor difference...

Thanks for the reply it's appreciated. The spring is in place, but I'm starting to think it may be a bad clutch, despite the fact it looks almost new. About to pull it down again tomorrow when I'm back in the workshop for a closer look.

If you are going down the 52mm big bore option, just a few hints on what to avoid. A few customers have brought in these Chinese aftermarket kits, with quality ranging from average to very poor. Piston rings were complete rubbish, many of the cylinders had off-set or out of shape inlet or...

Presently feeling like the Forest Gump of chainsaw repairers.... Customer brought in a mint condition 1986 Husqvarna 40 Rancher chainsaw, albeit with a minor piston scoring caused by bad fuel mix. Simple enough job, and an hour & half later the saw was running like new after a new piston &...

Thanks for all the replies so far....Seems to be an even split between the "can be done" and the "can't be done" camps. I'm fortunate that I have 2 of these saws available so I can play Dr Frankenstein, and better still, a customer who simply doesn't care if the experiment is a success or...

I'm looking for a thread posted a while back and seeking assistance either locating the tread, or hearing from members who've converted Husqvarna 550XP and 562XP saws back to a conventional carburettor. I presently have (2) 562XP saws that are dead with a highly annoyed owner who spent good...

Thanks for all the answers guy's, info very appreciated...in particular old Windsor catalogue.

Guys I'm just seeking some information regarding a customers 26" Windsor bar. Customer brought in a Windsor Speed-Tip 26" pro bar (3/8" x 058"). He has it fitted to a Husky 385xp and wanted a new chain. I'll be honest and say I haven't seen a 26" bar for maybe 10 to 15 years or more (very...

Checked with 3 Stihl dealers here in Sydney, and unfortunately all said the same that no such beast exists down under....The old orange AUD$85 critter is all we can get. Do you have a Stihl part number, as I would like to drop a line to the Stihl's Australian head office requesting likely...

Wishing to purchase a couple of Husqvarna 357XP or Jonsered CS2156 chainsaws. Don't mind if the saws are running or not, as they will ultimately be used for projects. I would prefer saws that are not too battered about physically, however will consider anything including parts you may have just...